參數資料
型號： M50FW080K5TP
廠商： 意法半導體
英文描述： 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
中文描述： 8兆1兆× 8，統一座3V電源閃存固件集線器
文件頁數： 32/56頁
文件大?。?/td> 292K
代理商： M50FW080K5TP
Firmware Hub (FWH) interface Configuration Registers
M50FW080
32/55
6
Firmware Hub (FWH) interface Configuration
Registers
When the Firmware Hub Interface is selected several additional registers can be accessed.
These registers control the protection status of the Blocks, read the General Purpose Input
pins and identify the memory using the Electronic Signature codes. See
Table 11
for the
memory map of the Configuration Registers.
6.1
Lock Registers
The Lock Registers control the protection status of the Blocks. Each Block has its own Lock
Register. Three bits within each Lock Register control the protection of each block, the Write
Lock Bit, the Read Lock Bit and the Lock Down Bit.
The Lock Registers can be read and written, though care should be taken when writing as,
once the Lock Down Bit is set, ‘1’, further modifications to the Lock Register cannot be made
until cleared, to ‘0’, by a reset or power-up.
See
Table 12
for details on the bit definitions of the Lock Registers.
6.1.1
Write Lock
The Write Lock Bit determines whether the contents of the Block can be modified (using the
Program or Block Erase Command). When the Write Lock Bit is set, ‘1’, the block is write
protected; any operations that attempt to change the data in the block will fail and the Status
Register will report the error. When the Write Lock Bit is reset, ‘0’, the block is not write
protected through the Lock Register and may be modified unless write protected through
some other means.
When V
PP
is less than V
PPLK
all blocks are protected and cannot be modified, regardless of
the state of the Write Lock Bit. If Top Block Lock, TBL, is Low, V
IL
, then the Top Block (Block
15) is write protected and cannot be modified. Similarly, if Write Protect, WP, is Low, V
IL
,
then the Main Blocks (Blocks 0 to 14) are write protected and cannot be modified.
After power-up or reset the Write Lock Bit is always set to ‘1’ (write protected).
6.1.2
Read Lock
The Read Lock bit determines whether the contents of the Block can be read (from Read
mode). When the Read Lock Bit is set, ‘1’, the block is read protected; any operation that
attempts to read the contents of the block will read 00h instead. When the Read Lock Bit is
reset, ‘0’, read operations in the Block return the data programmed into the block as
expected.
After power-up or reset the Read Lock Bit is always reset to ‘0’ (not read protected).
相關PDF資料
PDF描述
M50FW080N5P 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080N5TP 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB5P 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB5TP 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50LPW002 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
M50FW080N 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080N1 功能描述:閃存 3.6V 8M (1Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50FW080N1G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080N1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080N1TG 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*