- 您現在的位置：買賣IC網 > PDF目錄377830 > M50FW080NB5P (意法半導體) 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW080NB5P |
| 廠商： | 意法半導體 |
| 英文描述： | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 8兆1兆× 8，統一座3V電源閃存固件集線器 |
| 文件頁數： | 16/56頁 |
| 文件大?。?/td> | 292K |
| 代理商： | M50FW080NB5P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Signal descriptions
M50FW080
16/55
2.3
Supply signal descriptions
The Supply Signals are the same for both interfaces.
2.3.1
V
CC
supply voltage
The V
CC
Supply Voltage supplies the power for all operations (Read, Program, Erase etc.).
The Command Interface is disabled when the V
CC
Supply Voltage is less than the Lockout
Voltage, V
LKO
. This prevents Bus Write operations from accidentally damaging the data
during power up, power down and power surges. If the Program/Erase Controller is
programming or erasing during this time then the operation aborts and the memory contents
being altered will be invalid. After V
CC
becomes valid the Command Interface is reset to
Read mode.
A 0.1μF capacitor should be connected between the V
CC
Supply Voltage pins and the V
SS
Ground pin to decouple the current surges from the power supply. Both V
CC
Supply Voltage
pins must be connected to the power supply. The PCB track widths must be sufficient to
carry the currents required during program and erase operations.
2.3.2
V
PP
optional supply voltage
The V
PP
Optional Supply Voltage pin is used to select the Fast Program (see the Quadruple
Byte Program Command description) and Fast Erase options of the memory and to protect
the memory. When V
PP
< V
PPLK
Program and Erase operations cannot be performed and
an error is reported in the Status Register if an attempt to change the memory contents is
made. When V
PP
= V
CC
Program and Erase operations take place as normal. When V
PP
=
V
PPH
Fast Program (if A/A Mux interface is selected) and Fast Erase operations are used.
Any other voltage input to V
PP
will result in undefined behavior and should not be used.
V
PP
should not be set to V
PPH
for more than 80 hours during the life of the memory.
2.3.3
V
SS
ground
V
SS
is the reference for all the voltage measurements.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW080NB5TP | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50LPW002 | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K1T | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K5T | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW080NB5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5TG | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW080NB5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50G1041 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Multilayer Ceramic Capacitors |
| M50G1041-F | 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Multilayer Ceramic Capacitors COG (NPO). X7R & Z5U Capacitors |
發布緊急采購，3分鐘左右您將得到回復。