- 您現在的位置：買賣IC網 > PDF目錄377830 > M50FW080NB5P (意法半導體) 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW080NB5P |
| 廠商： | 意法半導體 |
| 英文描述： | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 8兆1兆× 8，統一座3V電源閃存固件集線器 |
| 文件頁數： | 30/56頁 |
| 文件大小： | 292K |
| 代理商： | M50FW080NB5P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Status Register
M50FW080
30/55
5.6
Program Suspend status (bit 2)
The Program Suspend Status bit indicates that a Program operation has been suspended
and is waiting to be resumed. The Program Suspend Status should only be considered valid
when the Program/Erase Controller Status bit is ‘1’ (Program/Erase Controller inactive);
after a Program/Erase Suspend command is issued the memory may still complete the
operation rather than entering the Suspend mode.
When the Program Suspend Status bit is ‘0’ the Program/Erase Controller is active or has
completed its operation; when the bit is ‘1’ a Program/Erase Suspend command has been
issued and the memory is waiting for a Program/Erase Resume command.
When a Program/Erase Resume command is issued the Program Suspend Status bit
returns to ‘0’.
5.7
Block Protection status (bit 1)
The Block Protection Status bit can be used to identify if the Program or Block Erase
operation has tried to modify the contents of a protected block. When the Block Protection
Status bit is to ‘0’ no Program or Block Erase operations have been attempted to protected
blocks since the last Clear Status Register command or hardware reset; when the Block
Protection Status bit is ‘1’ a Program or Block Erase operation has been attempted on a
protected block.
Once it is set to ‘1’ the Block Protection Status bit can only be reset to ‘0’ by a Clear Status
Register command or a hardware reset. If it is set to ‘1’ it should be reset before a new
Program or Block Erase command is issued, otherwise the new command will appear to fail.
Using the A/A Mux Interface the Block Protection Status bit is always ‘0’.
5.7.1
Reserved (Bit 0)
Bit 0 of the Status Register is reserved. Its value should be masked.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW080NB5TP | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50LPW002 | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K1T | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| M50LPW002K5T | 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW080NB5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5TG | 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW080NB5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50G1041 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Multilayer Ceramic Capacitors |
| M50G1041-F | 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Multilayer Ceramic Capacitors COG (NPO). X7R & Z5U Capacitors |
發布緊急采購，3分鐘左右您將得到回復。