- 您現在的位置：買賣IC網 > PDF目錄180240 > M7A3P400-FGG484 FPGA, 400000 GATES, 350 MHz, PBGA484 PDF資料下載
參數資料
| 型號： | M7A3P400-FGG484 |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 400000 GATES, 350 MHz, PBGA484 |
| 封裝： | 1 MM PITCH, GREEN, FBGA-484 |
| 文件頁數： | 209/246頁 |
| 文件大小： | 3010K |
| 代理商： | M7A3P400-FGG484 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁當前第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁
ProASIC3/E Flash Family FPGAs
v2.1
2-53
from programming to operating mode, the I/Os are
instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
Output buffer is disabled (with tristate value of high
impedance)
Input buffer is disabled (with tristate value of high
impedance)
Weak pull-up is programmed
GL
Globals
GL I/Os have access to certain clock conditioning circuitry
(and the PLL) and/or have direct access to the global
network (spines). Additionally, the global I/Os can be
used as I/Os, since they have identical capabilities.
Unused GL pins are configured as inputs with pull-up
resistors. See more detailed descriptions of global I/O
connectivity in the "Clock Conditioning Circuits" section
on page 2-15. All inputs labeled GC/GF are direct inputs
into the quadrant clocks. For example, if GAA0 is used
for an input, GAA1 and GAA2 are no longer available for
input to the quadrant globals. All inputs labeled GC/GF
are direct input into the chip level globals and the rest
are connected to the quadrant globals. The inputs to the
global network are multiplexed and only one input can
be used as a global input.
Refer to the "User I/O Naming Convention" section on
page 2-50 for a explanation of the naming of global
pins.
JTAG Pins
ProASIC3 devices have a separate bank for the dedicated
JTAG pins. The JTAG pins can be run at any voltage from
1.5 V to 3.3 V (nominal). VCC must also be powered for
the JTAG state machine to operate, even if the device is
in bypass mode; VJTAG alone is insufficient. Both VJTAG
and VCC to the ProASIC3 part must be supplied to allow
JTAG signals to transition the ProASIC3 device. Isolating
the JTAG power supply in a separate I/O bank gives
greater flexibility in supply selection and simplifies
power supply and PCB design. If the JTAG interface is
neither used nor planned for use, the VJTAG pin together
with the TRST pin could be tied to GND.
TCK
Test Clock
Test clock input for JTAG boundary scan, ISP, and UJTAG.
The TCK pin does not have an internal pull-up/down
resistor. If JTAG is not used, Actel recommends tying off
TCK to GND through a resistor placed close to the FPGA
pin. This prevents JTAG operation in case TMS enters an
undesired state.
Note that to operate at all VJTAG voltages, 500 Ω to 1 kΩ
will satisfy the requirements. Refer to Table 2-24 for
more information.
TDI
Test Data Input
Serial input for JTAG boundary scan, ISP, and UJTAG
usage. There is an internal weak pull-up resistor on the
TDI pin.
TDO
Test Data Output
Serial output for JTAG boundary scan, ISP, and UJTAG
usage.
TMS
Test Mode Select
The TMS pin controls the use of the IEEE1532 boundary
scan pins (TCK, TDI, TDO, TRST). There is an internal weak
pull-up resistor on the TMS pin.
TRST
Boundary Scan Reset Pin
The TRST pin functions as an active low input to
asynchronously initialize (or reset) the boundary scan
circuitry. There is an internal weak pull-up resistor on the
TRST pin. If JTAG is not used, an external pull-down
resistor could be included to ensure the test access port
(TAP) is held in reset mode. The resistor values must be
chosen from Table 2-24 and must satisfy the parallel
resistance value requirement. The values in Table 2-24
correspond to the resistor recommended when a single
device is used and the equivalent parallel resistor when
multiple devices are connected via a JTAG chain.
In critical applications, an upset in the JTAG circuit could
allow entering an undesired JTAG state. In such cases,
Actel recommends tying off TRST to GND through a
resistor placed close to the FPGA pin.
Note that to operate at all VJTAG voltages, 500 Ω to 1 kΩ
will satisfy the requirements.
Special Function Pins
NC
No Connect
This pin is not connected to circuitry within the device.
These pins can be driven to any voltage or can be left
floating with no effect on the operation of the device.
DC
Do Not Connect
This pin should not be connected to any signals on the
PCB. These pins should be left unconnected.
Table 2-24 Recommended Tie-Off Values for the TCK and
TRST Pins
VJTAG
Tie-Off Resistance
VJTAG at 3.3 V
200
Ω to 1 kΩ
VJTAG at 2.5 V
200
Ω to 1 kΩ
VJTAG at 1.8 V
500
Ω to 1 kΩ
VJTAG at 1.5 V
500
Ω to 1 kΩ
Notes:
1. Equivalent parallel resistance if more than one device is on
the JTAG chain.
2. The TCK pin can be pulled up/down.
3. The TRST pin be pulled down.
相關PDF資料 |
PDF描述 |
|---|---|
| M7A3P400-FPQ208 | FPGA, 400000 GATES, 350 MHz, PQFP208 |
| M7A3P400-FPQG208 | FPGA, 400000 GATES, 350 MHz, PQFP208 |
| M7A3P400-PQ208I | FPGA, 400000 GATES, 350 MHz, PQFP208 |
| M7A3P400-PQ208 | FPGA, 400000 GATES, 350 MHz, PQFP208 |
| M7A3P400-PQG208I | FPGA, 400000 GATES, 350 MHz, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M7A5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MEDIUM CURRENT SILICON RECTIFIERS |
| M7A9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MEDIUM CURRENT SILICON RECTIFIERS |
| M7AFS600-1FG256 | 制造商:Microsemi Corporation 功能描述:FPGA FUSION 600K GATES 1282.05MHZ 130NM 1.5V 256FBGA - Trays 制造商:Microsemi SOC Products Group 功能描述:FPGA FUSION 600K GATES 1282.05MHZ 130NM 1.5V 256FBGA - Trays |
| M7AFS600-1FG256ES | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:Actel Fusion Mixed-Signal FPGAs |
| M7AFS600-1FG256I | 制造商:Microsemi Corporation 功能描述:FPGA FUSION 600K GATES 1282.05MHZ 130NM 1.5V 256FBGA - Trays 制造商:Microsemi SOC Products Group 功能描述:FPGA FUSION 600K GATES 1282.05MHZ 130NM 1.5V 256FBGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。