- 您現在的位置：買賣IC網 > PDF目錄9499 > MAX1221BETX+ (Maxim Integrated Products)IC ADC/DAC 12BIT W/FIFO 36TQFNEP PDF資料下載
參數資料
| 型號： | MAX1221BETX+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 30/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC/DAC 12BIT W/FIFO 36TQFNEP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | ADC，DAC |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 225k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 2.7 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-TQFN 裸露焊盤（6x6） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MAX1221/MAX1223/MAX1343
12-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
36
______________________________________________________________________________________
Internally Timed Acquisitions and
Conversions Using the Serial Interface
ADC Conversions in Clock Mode 10
In clock mode 10, the wake-up, acquisition, conversion,
and shutdown sequence is initiated by writing a com-
mand byte to the conversion register, and is performed
automatically using the internal oscillator. This is the
default clock mode upon power-up. See Figure 8 for
clock mode 10 timing.
Initiate a scan by writing a command byte to the conver-
sion register. The MAX1221/MAX1223/MAX1343 then
power up, scan all requested channels, store the results
in the FIFO, and shut down. After the scan is complete,
EOC is pulled low and the results are available in the
FIFO. If a temperature measurement is requested, the
temperature result precedes all other FIFO results.
EOC
stays low until
CS is pulled low again. Wait until all con-
versions are complete before reading the FIFO. SPI
communications to the DAC and GPIO registers are per-
mitted during conversion. However, coupled noise may
result in degraded ADC SNR.
Externally Clocked Acquisitions and
Conversions Using the Serial Interface
ADC Conversions in Clock Mode 11
In clock mode 11, acquisitions and conversions are ini-
tiated by writing a command byte to the conversion
register and are performed one at a time using the
SCLK as the conversion clock. Scanning, averaging
and the FIFO are disabled, and the conversion result is
available at DOUT during the conversion. Output data
is updated on the rising edge of SCLK in clock mode
11. See Figure 9 for clock mode 11 timing.
Initiate a conversion by writing a command byte to the
conversion register followed by 16 SCLK cycles. If
CS
is pulsed high between the eighth and ninth cycles, the
pulse width must be less than 100s. To continuously
convert at 16 cycles per conversion, alternate 1 byte of
zeros (NOP byte) between each conversion byte. If 2
NOP bytes follow a conversion byte, the analog cells
power down at the end of the second NOP. Set the
FBGON bit to one in the reset register to keep the inter-
nal bias block powered.
If reference mode 00 is requested, or if an external refer-
ence is selected but a temperature measurement is being
requested, wait 45s with
CS high after writing the con-
version byte to extend the acquisition and allow the inter-
nal reference to power up. To perform a temperature
measurement, write 24 bytes (192 cycles) of zeros after
the conversion byte. The temperature result appears on
DOUT during the last 2 bytes of the 192 cycles.
Conversion-Time Calculations
The conversion time for each scan is based on a num-
ber of different factors: conversion time per sample,
samples per result, results per scan, if a temperature
measurement is requested, and if the external refer-
ence is in use. Use the following formula to calculate
the total conversion time for an internally timed conver-
sion in clock mode 00 and 10 (see the
Electrical
Characteristics, as applicable):
Total conversion time =
tCNV x nAVG x nSCAN + tTS + tINT-REF,SU
where:
tCNV = tDOV (where tDOV is dependent from the clock
and reference mode selected.)
SCLK
DOUT
MSB1
LSB1
MSB2
(ACQUISITION1)
(ACQUISITION2)
(CONVERSION1)
DIN
(CONVERSION BYTE)
CS
EOC
Figure 9. Clock Mode 11—Externally Timed Acquisition, Sampling, and Conversion without
CNVST
相關PDF資料 |
PDF描述 |
|---|---|
| MAX188DCWP+ | IC DAS 8CH 12BIT T/H LP 20-SOIC |
| MAX1407CAI+ | IC DAS 16BIT LP 28-SSOP |
| MAX1414CAI+ | IC DAS 16BIT LP 28-SSOP |
| NBXDPA019LN1TAG | IC CLK XO LVDS 125/250MHZ 6CLCC |
| MAX181CCQH+D | IC DAS 12BIT 100KSPS 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1221BETX+ | 功能描述:ADC / DAC多通道 12-Bit 8Ch 300ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1221BETX+T | 功能描述:ADC / DAC多通道 12-Bit 8Ch 300ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1221BETX-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1223BETX | 制造商:Maxim Integrated Products 功能描述:12-BIT MULTICHANNEL ADC/DAC WITH F - Rail/Tube |
| MAX1223BETX+ | 制造商:Maxim Integrated Products 功能描述:12-BIT, MULTICHANNEL ADCS/DACS WITH FIFO, TEMPERATURE SENSIN - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC ADC 12BIT QFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel |
發布緊急采購，3分鐘左右您將得到回復。