- 您現在的位置：買賣IC網 > PDF目錄18710 > MAXQ2010-KIT# (Maxim Integrated)EVALUATION KIT FOR MAX2010 PDF資料下載
參數資料
| 型號： | MAXQ2010-KIT# |
| 廠商： | Maxim Integrated |
| 文件頁數： | 18/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION KIT FOR MAX2010 |
| 標準包裝： | 1 |
| 類型： | 微控制器 |
| 已供物品： | 板，線纜，CD，文檔，電源 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
MAXQ2010
16-Bit Mixed-Signal Microcontroller
with LCD Interface
______________________________________________________________________________________
25
Supply Voltage Monitor
The supply voltage monitor can detect if the supply volt-
age has fallen below a user-selectable level. If this hap-
pens, the microcontroller can be programmed to
generate an interrupt to inform the system. The detec-
tion level is set using the supply voltage threshold bit
(SVTH) and can be adjusted from 2.7V to 3.5V in 0.1V
increments. Setting the SVMEN bit to 1 enables the sup-
ply voltage monitor. Once the monitoring circuitry is sta-
ble and ready for operation, the supply voltage monitor
ready (SVMRDY) flag is set to 1. The default set point is
2.7V (SVTH[3:0] = 07h). Care must be taken not to set
the set point below 2.7V as SVM interrupts may not
occur because the brownout monitor may activate first.
The supply voltage monitor causes a switchback to
occur if the supply voltage falls below the threshold
value and the supply voltage monitor interrupt is
enabled (SVMIE = 1).
The supply voltage monitor remains operational in stop
mode if the supply voltage monitor stop mode enable
bit (SVMSTOP) is set to 1. Clearing SVMSTOP to 0 dis-
ables the supply voltage monitor on entry to stop mode
if the SVM peripheral is enabled. If the supply voltage
monitor is enabled during stop mode, an SVMI interrupt
causes the processor to exit stop mode if enabled
(SVMIE = 1).
Serial Peripherals
The microcontroller supports two independent USARTs
as well as I2C master/slave and SPI master communi-
cation ports.
USART Serial Ports
The independent USARTs provide transmit and receive
signals to communicate with other RS-232 interface-
enabled devices, as well as PCs and serial modems
when paired with an external RS-232 line driver/receiver.
The dual independent USARTs can communicate simulta-
neously at different baud rates with two separate periph-
erals. The USART can detect framing errors and indicate
the condition through a user-accessible software bit.
PD.x
SF DIRECTION
SF ENABLE
MUX
PO.x
VDDIO
SF OUTPUT
VDDIO
WEAK
I/O PAD
PORT PIN
INTERRUPT
FLAG
PI.x OR SF INPUT
EIES.x
TYPE D PORT ONLY
DETECT
CIRCUIT
MAXQ2010
Figure 6. Type C/D Port Pin Schematic
相關PDF資料 |
PDF描述 |
|---|---|
| GLAC01E7B | SWTCH WOBBLE/COIL SPRING SPDT |
| 78602/9C | TRANSFORMER 1:1:1 10MH 56VUS |
| 78602/2C | TRANSFORMER 1:1:1 500UH 10VUS |
| 78604/9C | TRANSFORMER 2:1 10MH 56VUS |
| 78604/4C | TRANSFORMER 2:1 100UH 4VUS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAXQ2010-KIT# | 功能描述:數據轉換 IC 開發工具 MAXQ2010 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAXQ2010-RFX+ | 功能描述:16位微控制器 - MCU 16-Bit Mixed-Signal MCU w/LCD Interface RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ2KUSB-KIT# | 功能描述:開發板和工具包 - 其他處理器 MAXQ2000 Eval Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| MAXQ305 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Voltage Microcontroller with Infrared Module |
| MAXQ305J-0000+ | 功能描述:8位微控制器 -MCU MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。