- 您現在的位置：買賣IC網 > PDF目錄18710 > MAXQ2010-KIT# (Maxim Integrated)EVALUATION KIT FOR MAX2010 PDF資料下載
參數資料
| 型號： | MAXQ2010-KIT# |
| 廠商： | Maxim Integrated |
| 文件頁數： | 21/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVALUATION KIT FOR MAX2010 |
| 標準包裝： | 1 |
| 類型： | 微控制器 |
| 已供物品： | 板，線纜，CD，文檔，電源 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
MAXQ2010
16-Bit Mixed-Signal Microcontroller
with LCD Interface
28
______________________________________________________________________________________
(ADPMO = 0), the ADC waits for 20 ADCCLK before
starting the first conversion. This allows the ADC time to
set up.
If ADPMO = 1, an ADC conversion is initiated as soon
as ADCONV is set to 1. ADC operation is aborted upon
entry into PMM or stop mode.
The ADCONV bit is set at the beginning of the conver-
sion process and remains set until the conversion
process is finished. In single-sequence mode, this bit
remains set until the ADC has finished conversion on
the last channel in the sequence. In continuous mode,
the ADCONV bit remains set until the continuous mode
is stopped. Writing a 0 to the ADCONV bit stops ADC
operation at the completion of the current ADC conver-
sion. The new data is written to the data buffer.
An A/D conversion takes 16 ADCCLK cycles to com-
plete. Three of the 16 ADCCLK cycles are used for
sample acquisition. The ADCCLK is derived from the
system clock with divide ratio defined by the ADC clock
divider bits (ADCCLK). Therefore, with 16 ADCCLK to
acquire one data, the fastest ADC rate = sysclk/16
(ADCCLK = 0h, ADACQEN = 0h). With a 10MHz sys-
tem clock, this is theoretically equivalent to 10MHz/16
value Msps. Note, however, that the ADC conversion is
limited to 300ksps.
If the ADC data-available interrupt is enabled (ADDAIE
= 1), an interrupt is generated to the CPU when ADDAI
= 1. Once set, the ADDAI flag can be cleared by soft-
ware writing a 0 or at the start of a conversion process
when ADCONV is set to 1. The data-available interrupt
flag (ADDAI) can optionally be set by using the ADC
data-available interrupt interval bits (ADDAINV). The
ADDAI can be set in 1, 2, 3, 4, 5, 6, 7, 8, 12, or 16 sam-
ples intervals. For a sequence that uses only one con-
figuration register, setting ADDAINV = 00 generates an
interrupt with the same interval as ADDAINV = 01, both
of which set the ADDAI at every ADC sample. When the
ADDAI is set, the last memory location written by ADC
will also be written to ADDADDR.
LCD Controller
The MAXQ2010 microcontroller incorporates an LCD
controller that interfaces to common low-voltage dis-
plays. By incorporating the LCD controller into the
microcontroller, the design requires only an LCD glass
rather than a considerably more expensive LCD mod-
ule. Every character in an LCD glass is composed of
one or more segments, each of which is activated by
selecting the appropriate segment and common signal.
The microcontroller can multiplex combinations of up to
43 segment outputs (SEG0 to SEG42) and four com-
mon signal outputs (COM0 to COM3). Unused segment
outputs can be used as general-purpose port pins.
The segments are easily addressed by writing to dedi-
cated display memory. Once the LCD controller set-
tings and display memory have been initialized, the
21-byte display memory is periodically scanned, and
the segment and common signals are generated auto-
matically at the selected display frequency. No addi-
tional processor overhead is required while the LCD
controller is running. Unused display memory can be
used for general-purpose storage.
The design is further simplified and cost reduced by
the inclusion of software-adjustable internal voltage-
INPUT
MULTIPLEXER
AND
TRACK/HOLD
12-BIT
SAR
INTERNAL
REFERENCE
EXTERNAL
REFERENCE
AVDD
ADC REFERENCE
ADC CONTROL
AN7
AVDD
AVSS
ADC INTERRUPT
AN6
AN5
AN4
AN3
AN2
AN1
AN0
Figure 7. ADC Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| GLAC01E7B | SWTCH WOBBLE/COIL SPRING SPDT |
| 78602/9C | TRANSFORMER 1:1:1 10MH 56VUS |
| 78602/2C | TRANSFORMER 1:1:1 500UH 10VUS |
| 78604/9C | TRANSFORMER 2:1 10MH 56VUS |
| 78604/4C | TRANSFORMER 2:1 100UH 4VUS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAXQ2010-KIT# | 功能描述:數據轉換 IC 開發工具 MAXQ2010 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAXQ2010-RFX+ | 功能描述:16位微控制器 - MCU 16-Bit Mixed-Signal MCU w/LCD Interface RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MAXQ2KUSB-KIT# | 功能描述:開發板和工具包 - 其他處理器 MAXQ2000 Eval Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| MAXQ305 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Voltage Microcontroller with Infrared Module |
| MAXQ305J-0000+ | 功能描述:8位微控制器 -MCU MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。