參數資料
型號： MB90V495G
廠商： Fujitsu Limited
英文描述： 16-bit Proprietary Microcontroller
中文描述： 16位微控制器專有
文件頁數： 10/78頁
文件大?。?/td> 746K
代理商： MB90V495G
MB90895 Series
10
I
HANDLING DEVICES
Do Not Exceed Maximum Rating (preventing “l(fā)atch up”)
On a CMOS IC, latch-up may occur when applying a voltage higher than Vcc or a voltage lower than Vss to
input or output pin, which has no middle or high withstand voltage. Latch-up may also occur when a voltage
exceeding maximum rating is applied across Vcc and Vss.
Latch-up causes drastic increase of power current, which may lead to destruction of elements by heat. Extreme
caution must be taken not to exceed maximum rating.
When turning on and off analog power source, take extra care not to apply an analog power voltages (AVcc
and AVR) and analog input voltage that are higher than digital power voltage (Vcc).
Handling Unused Pins
Leaving unused input pins open may cause permanent destruction by malfunction or latch-up. Apply pull-up
or pull-down process to the unused pins using resistors of 2 k
or higher. Leave unused input pins open under
output status, or process as input pins if they are under input status.
Using External Clock
When using an external clock, drive only X0 pin and leave X1 pin open. An example of using an external clock
is shown below.
Notes When Using No Sub Clock on MB90F897
If an oscillator is not connected to X0A and X1A pin, apply pull-down resistor to X0A pin and leave X1A pin open.
About Power Supply Pins
If two or more Vcc and Vss exist, the pins that should be at the same potential are connected to each other
inside the device. For reducing unwanted emissions and preventing malfunction of strobe signals caused by
increase of ground level, however, be sure to connect the Vcc and Vss pins to the power source and the ground
externally.
Pay attention to connect a power supply to Vcc and Vss of MB90895 series device in a lowest-possible
impedance.
Near pins of MB90895 series device, connecting a bypass capacitor is recommended at 0.1
μ
F across Vcc
and Vss.
Crystal Oscillator Circuit
Noises around X0 and X1 pins cause malfunctions on a MB90895 series device. Design a print circuit so that
X0 and X1 pins, an crystal oscillator (or a ceramic oscillator), and bypass capacitor to the ground become as
close as possible to each other. Furthermore, avoid wires to X0 and X1 pins crossing each other as much as
possible.
Print circuit designing that surrounds X0 and X1 pins with grounding wires, which ensures stable operation,
is strongly recommended.
Caution on Operations during PLL Clock Mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
X1
X0
Open
MB90895 series
Using external clock
相關PDF資料
PDF描述
MB90F897PMT 10-Bit Buffers/Drivers With 3-State Outputs 24-CDIP -55 to 125
MB90F897S 10-Bit Buffers/Drivers With 3-State Outputs 28-LCCC -55 to 125
MB90F897SPMT 10-Bit Buffers/Drivers With 3-State Outputs 24-CDIP -55 to 125
MB90M405 Octal Edge-Triggered D-type Flip-Flops With Clear 20-CFP -55 to 125
MB90M407 Octal Edge-Triggered D-type Flip-Flops With Clear 20-LCCC -55 to 125
相關代理商/技術參數
參數描述
MB-910 制造商:Circuit Test 功能描述:BREADBOARD WIRING KIT - 350 PCS
MB9100100 制造商:COM/DUO 功能描述:FAN 4-6WKS
MB9100-100 制造商:COM/DUO 功能描述:FAN 4-6WKS
MB91101 制造商:Panasonic Industrial Company 功能描述:IC
MB91101A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit RISC Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*