參數資料
型號: MC13211
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: ZigBee- Compliant Platform - 2.4 GHz Low Power Transceiver for the IEEE 802.15.4 Standard plus Microcontroller(ZigBee平臺- 為IEEE 802.15.4標準和微控制器設計的2.4 GHz低功率收發器)
中文描述: ZigBee兼容平臺- 2.4 GHz的低功耗收發器符合IEEE 802.15.4標準加微控制器(ZigBee的平臺-為IEEE 802.15.4無線標準和微控制器設計的2.4 GHz的低功率收發器)
文件頁數: 26/70頁
文件大?。?/td> 802K
代理商: MC13211
MC13211/212/213/214 Technical Data, Rev. 0.0,
26
Freescale Semiconductor
5.2
MCU Modes of Operation
The MCU has multiple operational modes to facilitate maximum system performance while also providing
low-power modes. In the MC1321x, the MCU can use the following modes:
Run
Wait
Stop2
Stop3
NOTE
The MCU can also be programmed for Stop1 mode, but this mode IS NOT
USABLE. The reset to the modem function is controlled by an MCU GPIO
and the GPIO state must be maintained during the MCU “stop” condition.
Stop1 mode does not control I/O states as required during modem power
down condition.
5.2.1
Run Mode
This is the normal operating mode for the HCS08. This mode is selected when the BKGD/MS pin is high
at the rising edge of reset. In this mode, the CPU executes code from internal memory with execution
beginning at the address fetched from memory at $FFFE:$FFFF after reset.
5.2.2
Wait Mode
Wait Mode is entered by executing a WAIT instruction. Upon execution of the WAIT instruction, the CPU
enters a low-power state in which it is not clocked. The I bit in CCR is cleared when the CPU enters the
wait mode, enabling interrupts. When an interrupt request occurs, the CPU exits the wait mode and
resumes processing, beginning with the stacking operations leading to the interrupt service routine.
While the MCU is in Wait Mode, there are some restrictions on which background debug commands can
be used. Only the BACKGROUND command and memory-access-with-status commands are available
when the MCU is in wait mode. The memory-access-with-status commands do not allow memory access,
but they report an error indicating that the MCU is in either stop or wait mode. The BACKGROUND
command can be used to wake the MCU from Wait Mode and enter active background mode.
5.2.3
Stop 2
The Stop2 Mode provides very low standby power consumption and maintains the contents of RAM and
the current state of all of the I/O pins. Stop2 can be entered only if the LVD circuit is not enabled in Stop
Modes (either LVDE or LVDSE not set).
Before entering Stop2 Mode, the user must save the contents of the I/O port registers, as well as any other
memory-mapped registers they want to restore after exit of Stop2, to locations in RAM. Upon exit of
Stop2, these values can be restored by user software before pin latches are opened.
相關PDF資料
PDF描述
MC14467P Low-Power CMOS Ionization Smoke Detector IC
MC14467P1 Other Analog Circuits
MC14467P-1 Low-Power CMOS Ionization Smoke Detector IC
MC14467-1 Low-Power CMOS Ionization Smoke Detector IC
MC14467P1 Low-Power CMOS Ionization Smoke Detector IC
相關代理商/技術參數
參數描述
MC13211_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ZigBee⑩- Compliant Platform -2.4 GHz Low Power Transceiver for the IEEE㈢ 802.15.4 Standard plus Microcontroller
MC13211R2 功能描述:射頻收發器 SIP 802.15.4 2.4GHZ 16KB RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
MC13212 功能描述:射頻收發器 TOROWEAP IC 32K RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
MC13212R2 功能描述:射頻收發器 SIP 802.15.4 2.4GHZ 32KB RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
MC13213 功能描述:射頻收發器 TOROWEAP IC 60K RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray