- 您現在的位置：買賣IC網 > PDF目錄359132 > MC33394 (飛思卡爾半導體(中國)有限公司) Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源) PDF資料下載
參數資料
| 型號： | MC33394 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | CAN |
| 英文描述： | Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源) |
| 中文描述： | 開關電源的多線性穩壓器和高速CAN收發器（帶有多個線性穩壓器和高速的CAN收發器的開關方式電源） |
| 文件頁數： | 17/44頁 |
| 文件大小： | 641K |
| 代理商： | MC33394 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
17
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
4.2.6. Switching Regulator Output Voltage Sense
(VPRE_S)
This is the switching regulator output voltage sense input.
The switcher output voltage VPRE is divided by an internal
resistor divider and compared with the bandgap reference
voltage (see Figure 4).
Refer to Section 5 Application Information for detailed
description of the switching regulator operation.
Figure 4. Switching Regulator Block Diagram
BUCK &
BOOST
CONTROL
LOGIC
CURRENT
LIMIT
SOFT
START
+
–
–
+
FEED
FORWARD
RAMP
GENERATOR
THERMAL
LIMIT
SWITCHER
OSCILLATOR
200 kHz
SWITCHER
MODE
ENABLE
Vbg
+
–
PWM
COMP
Vbg
Vbg
VPRE
COMP
BOOTSTRAP
VBAT
+
–
BOOST
COMP
Vbg
1.25 V
Vbg
1.25 V
Vbg
1.25 V
E/A
LS
DRIVER
HS
DRIVER
VPRE
VPRE
BOOT
SW1
VPRE
SW2G
VPRE_S
INV
VCOMP
40 k
11.7 k
4.3. Voltage Regulator (VDDH)
The VDDH output is a linearly regulated +5.0 +/– 0.10V
voltage supply capable of sourcing a maximum of 400 mA
steady state current from VPRE (+5.6 V) for VBAT voltages
from +4.0 V to +26.5 V (+45V transient). This regulator
incorporates current limit short circuit protection and thermal
shut down protection. The voltage output is stable under all
load/line conditions. However, the designer must consider
ripple and high frequency filtering as well as regulator
response, when choosing external components. See Table 1
in the Applications Information section for recommended
output capacitor parameters.
NOTE :
Backfeeding into the VDDH output can cause problems
during the power up sequence. Refer to the Electrical
Characteristics VDDH Regulator Section for the maximum
allowed backfed current into the VDDH output.
4.4. Tracking Voltage Regulator (VPP)
This linearly regulated +5.0 V/+3.3 V (SPI selectable)
voltage supply is capable of sourcing 150 mA of steady state
current from VPRE (+5.6 V) for VBAT voltage from +4.0 V to
+26.5 V (up to +45V transient). It tracks the VDDH or VDD3_3
output, and incorporates current limit short circuit protection
and over temperature shut down protection. This output is
intended for FLASH memory programming and includes a
dedicated enable pin (VPP_EN). The regulator enable can
also be controlled through the SPI interface but requires both
the VPP_EN pin and the SPI bit (EN_VPP bit) to be high to
enable. The selection of tracking VDDH or VDD3_3 is
controlled by the VPP_V bit in the SPI. Logic “1” selects VDDH
(default), logic “0” selects VDD3_3. The voltage output is
stable under all load/line conditions. However, the designer
must consider ripple and high frequency filtering as well as
regulator response when choosing external components. See
Table 1 for recommended output capacitor parameters.
The VPP tracking regulator should not be used in parallel
with the VDDH regulator, because this arrangement can
corrupt the proper power sequencing of the IC.
4.5. Tracking Voltage Regulator (VREFn)
The outputs of the VREF1, VREF2, VREF3 linear regulators
are 100 mA at +5.0 V. They track the VDDH output. The power
supplies are designed to supply power to sensors that are
located external to the module. These regulators may be
enabled or disabled via the SPI, which also provides fault
reporting for these regulators. They are protected for short to
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC33395 | Three-Phase Gate Driver IC(3相柵極驅動器) |
| MC33397 | Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(帶SPI和并口輸入控制的2或6低端開關) |
| MC33399 | “Local Interconnect Network” Physical Interface(“本地互聯網”（LIN）物理接口) |
| MC33486 | Dual High Side Switch for H-Bridge Automotive Applications(適合于H橋自動應用的雙高端開關) |
| MC33661 | LIN Enhanced Physical Interface(LIN網增強型物理接口) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33394DH | 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| MC33395DWB | 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33395DWBR2 | 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33395EW | 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MC33395EWR2 | 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。