- 您現在的位置：買賣IC網 > PDF目錄45220 > MC68HC05E6CFB (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MC68HC05E6CFB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | PLASTIC, QFP-44 |
| 文件頁數： | 49/140頁 |
| 文件大?。?/td> | 1584K |
| 代理商： | MC68HC05E6CFB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁
Modes of Operation and Pin Descriptions
MC68HC05E6 — Rev. 1.0
Modes of Operation and Pin Descriptions
Bootloader
functions
The bootloader code deals with the copying of user code from an
external EPROM into the on-chip EPROM. The bootloader function can
only be used with an external EPROM. The bootloader performs a
programming pass followed by a verify pass.
Two pins, PC0 and PC1, are used to drive the PROG and VERF LED
outputs. While the EPROM is being programmed, the PROG LED lights
up; when programming is complete, the internal EPROM contents are
compared to that of the external EPROM and, if they match exactly, the
VERF LED lights up.
The EPROM must be in the erased state before performing a program
cycle. The erased state of the EPROM is $00.
EPROM
programming
instructions
The following procedure should be carried out when programming the
EPROM. In order to prevent damage to the device, VDD should always be
applied to the part before VPP when applying power. Similarly, VPP should
be removed from the part before VDD when switching the power off.
1. Turn off power to the circuit.
2. Install the MCU and the EPROM.
3. Select the bootloader function:
Program 1 byte: Open S1 and S2 and close S3.
Program 4 bytes: Open S1, S2 and S3.
Verify only: Open S1 and S3 and close S2.
4. Close switch S4 to hold the MCU in reset.
5. Apply VDD to the circuit.
6. Apply the EPROM programming voltage (VPP) to the circuit.
7. Open switch S4 to take the MCU out of reset.
During programming the PROG LED turns on and is switched off
when the verification routine begins. If verification is successful,
the VERF LED turns on. If the bootloader finds an error during
verification, it puts the error address on the external address bus
and stops running.
8. Close switch S4 to hold the MCU in reset.
9. Remove the VPP voltage.
10. Remove the VDD voltage.
NOTE:
EPROM programming must be carried out at room temperature.
4-pin
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05E6CDW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| MC68HC05E6MFB | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05E6VDWR2 | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| MC68HC705E6MFB | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC705E6CFB | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05E6DW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05E6FB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05E6MDW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05E6MFB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05E6VDW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
發布緊急采購，3分鐘左右您將得到回復。