參數資料
型號: MC68L11F1CFN3
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, EEPROM, MICROCONTROLLER, PQCC68
封裝: PLASTIC, LCC-68
文件頁數: 110/174頁
文件大小: 981K
代理商: MC68L11F1CFN3
MOTOROLA
OPERATING MODES AND ON-CHIP MEMORY
MC68HC11F1
4-2
TECHNICAL DATA
The bootstrap ROM contains a small program which initializes the SCI and allows the
user to download a program of up to 1024 bytes into on-chip RAM. After a four-char-
acter delay, or after receiving the character for address $03FF, control passes to the
loaded program at $0000. An external pull-up resistor is required when using the SCI
transmitter pin (TxD) because port D pins are configured for wired-OR operation by
the bootloader. In bootstrap mode, the interrupt vectors point to RAM. This allows the
use of interrupts through a jump table. Refer to Motorola application note AN1060,
M68HC11 Bootstrap Mode.
4.2 On-Chip Memory
The MC68HC11F1 contains 1024 bytes of on-chip RAM and 512 bytes of EEPROM.
The bootloader ROM occupies 256 bytes. The CONFIG register is implemented as a
separate EEPROM byte.
4.2.1 Mapping Allocations
Memory locations for on-chip resources are the same for both expanded and single-
chip modes. The 96-byte register block originates at $1000 after reset and can be
placed at any other 4-Kbyte boundary ($x000) after reset by writing an appropriate val-
ue to the INIT register. Refer to Figure 4-1, which illustrates the memory map.
The on-board 1024-byte RAM is initially located at $0000 after reset. If RAM and reg-
isters are both mapped to the same 4-Kbyte boundary, the first 96 bytes of RAM are
inaccessible (registers have higher priority). Remapping is accomplished by writing
appropriate values to the INIT register.
The 512-byte EEPROM array is initially located at $FE00 after reset when EEPROM
is enabled in the memory map by the CONFIG register. In expanded and special test
modes EEPROM can be placed at any other 4-Kbyte boundary ($xE00) by program-
ming bits EE[3:0] in the CONFIG register to an appropriate value. In single-chip and
bootstrap modes the EEPROM is forced on and cannot be remapped.
In special bootstrap mode, a bootloader ROM is enabled at locations $BF00–$BFFF.
The vectors for special bootstrap mode are contained in the bootloader program. The
boot ROM fills 256 bytes of the memory map even though not all locations are used.
相關PDF資料
PDF描述
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68SZ328VH66V 66 MHz, RISC PROCESSOR, PBGA196
MC74F2970N DRAM CONTROLLER, PDIP24
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11K1FN2R2 制造商:Motorola Inc 功能描述:
MC68L11K1FUE2 功能描述:8位微控制器 -MCU 8B MCU L-VOLTAGE-EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT