參數資料
型號: MC68L11F1CFN3
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, EEPROM, MICROCONTROLLER, PQCC68
封裝: PLASTIC, LCC-68
文件頁數: 86/174頁
文件大?。?/td> 981K
代理商: MC68L11F1CFN3
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁
MC68HC11F1
PIN DESCRIPTIONS
MOTOROLA
TECHNICAL DATA
2-5
2.5 Four Times E-Clock Frequency Output (4XOUT)
Although the circuit shown in Figure 2-6 will work for any M68HC11 MCU, the
MC68HC11F1 has an additional clock output that is four times the E-clock frequency.
This output (4XOUT) can be used to directly drive the EXTAL input of another
M68HC11 MCU. Refer to Figure 2-7. The 4XOUT output is enabled after reset and
can be disabled by clearing the CLK4X bit in the OPT2 register.
Figure 2-7 4XOUT Signal Driving a Second MCU
2.6 Interrupt Request (IRQ)
The IRQ input provides a means of generating asynchronous interrupt requests for the
CPU. Either falling-edge triggering or low-level triggering is selected by the IRQE bit
in the OPTION register. IRQ is always configured for level-sensitive triggering at reset.
Connect an external pull-up resistor, typically 4.7 k
, to VDD when IRQ is used in a
level-sensitive wired-OR configuration. Refer to SECTION 5 RESETS AND INTER-
2.7 Non-Maskable Interrupt (XIRQ)
The XIRQ input provides a means of requesting a non-maskable interrupt after reset
initialization. During reset, the X bit in the condition code register (CCR) is set and any
interrupt is masked until MCU software enables it. Because the XIRQ input is level
sensitive, it can be connected to a multiple-source wired-OR network with an external
pull-up resistor to VDD. XIRQ is often used as a power loss detect interrupt.
Whenever XIRQ or IRQ are used with multiple interrupt sources (IRQ must be config-
ured for level-sensitive operation if there is more than one source of IRQ interrupt),
each source must drive the interrupt input with an open-drain type of driver to avoid
contention between outputs. There should be a single pull-up resistor near the MCU
interrupt input pin (typically 4.7 k
). There must also be an interlock mechanism at
each interrupt source so that the source holds the interrupt line low until the MCU rec-
ognizes and acknowledges the interrupt request. If one or more interrupt sources are
still pending after the MCU services a request, the interrupt line will still be held low
and the MCU will be interrupted again as soon as the interrupt mask bit in the condition
code register (CCR) is cleared (normally upon return from an interrupt). Refer to SEC-
EXTAL
4XOUT
MC68HC11F1
NC OR
10 k – 100 k
LOAD
XTAL
EXTAL
SECOND
XTAL
MCU
OSCILLATOR
CIRCUIT OR
CMOS-COMPATIBLE
CLOCK
相關PDF資料
PDF描述
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68SZ328VH66V 66 MHz, RISC PROCESSOR, PBGA196
MC74F2970N DRAM CONTROLLER, PDIP24
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11K1FN2R2 制造商:Motorola Inc 功能描述:
MC68L11K1FUE2 功能描述:8位微控制器 -MCU 8B MCU L-VOLTAGE-EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT