參數資料
型號： MCP25050-E/SL
廠商： Microchip Technology
文件頁數： 20/66頁
文件大小： 0K
描述： IC I/O EXPANDER CAN 8B 14SOIC
標準包裝： 57
接口： CAN
輸入/輸出數： 8
中斷輸出： 無
頻率 - 時鐘： 25MHz
電源電壓： 4.5 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 14-SOIC
包裝： 管件
包括： ADC，存儲器，PWM
其它名稱： MCP25050E/SL
2007 Microchip Technology Inc.
DS21664D-page 27
MCP2502X/5X
4.5
Automatic Transmission
The MCP2502X/5X can automatically initiate four
different message types to indicate the following
situations:
Edge detected on a digital input (TXID2).
Threshold exceeded on an analog input (TXID2).
Error condition (Read Error output message).
Scheduled transmissions (TXID0).
The buffers have an implied transmit priority, where
buffer 2 is the highest and buffer 0 is the lowest.
Therefore, multiple message buffers can be requested
for transmission and each one will be sent in order of
priority.
4.5.1
DIGITAL INPUT EDGE DETECTION
Each GPIO pin configured as a digital input can be
individually configured to automatically transmit a
message when a defined edge occurs, as explained in
the GPIO module section. When transmitting this
message, the MCP2502X/5X uses TXID2. The DLC is
set to two and the first two bytes of the Read A/D
registers (IOINTFL and GPIO) are sent.
4.5.2
ANALOG INPUT THRESHOLD
DETECTION
Each GPIO pin that has been configured as an analog
input can be individually configured to automatically
transmit a message when a threshold is exceeded as
described in the Analog-to-Digital Converter Module
section. The MCP2502X/5X sends TXID2 when
transmitting this message. The DLC is set to eight and
the eight bytes of the ‘Read A/D Registers’ are sent.
4.5.2.1
Hysteresis Function
This function is automatic and will insure that an analog
value that is on the compare edge (i.e., toggling LSb)
does not fill the CAN bus with continuous A/D message
transmissions.
The hysteresis uses the two LSb’s of the compare
register. These two bits are forced and are not
configurable by the user. They will be forced to either
b’00’
or b’11’, depending on the compare polarity. If
configured for A/D result > compare register, the
automatic transmission will occur when the A/D value
is greater than or equal to b’nnnn nnnn 11’ and
reset when less than or equal to b’nnnn nnnn 00’.
The opposite conditions must occur if the compare
polarity is set for A/D result < compare register.
A hysteresis example:
The user sets the upper-eight bits of the 10-bit
compare register (ADCMP0H). The lower-two bits
of the compare register are not configurable by
the user and are forced to either b’11’ or b’00’
depending on the polarity of the compare
threshold (i.e., transmit is triggered above or
below the compare value via the IOINTPO
register).
The user sets the polarity of the compare
threshold (IOINTPO). In this example, the
threshold is set for triggering a message on an
A/D > compare register. The two LSb’s are forced
to b’11’.
When the A/D conversion exceeds the compare
register (b’nnnn nnnn 11’), an automatic
transmission will occur once.
In order for the automatic transmission to occur
again, the A/D value must first drop below the
compare register b’nnnn nnnn 00’ and then
back above the compare register
b’nnnn nnnn 11’
.
FIGURE 4-1:
HYSTERESIS
FUNCTION
4.5.3
ERROR CONDITION
The MCP2502X/5X can be configured to automatically
transmit a message whenever one or more of the
following error conditions occur:
Receiver has entered error-warning state
Receiver has entered error-passive state
Transmitter has entered error-warning state
Transmitter has entered error-passive state
A Receive buffer has overflowed
Note:
The GPIO register that is sent with the
message (data byte 2) can be ignored if
there are no digital inputs enabled for
change-of-state, as it contains no useful
information for the Analog Input Threshold
Detect function.
LSbs = b’11’
Set to Trigger when A/D>Compare Register
LSbs = b’00’
LSbs = b’11’
LSbs = b’00’
Set to Trigger when A/D<Compare Register
A/D above compare,
Message sent
A/D above compare,
Message sent
A/D below compare,
Reset
A/D below compare,
Message sent
A/D below compare,
Message sent
A/D above compare,
Reset
相關PDF資料
PDF描述
MCP25050-E/P IC I/O EXPANDER CAN 8B 14DIP
MCP25055T-I/SL IC I/O EXPANDER CAN 8B 14SOIC
MCP25055-I/P IC I/O EXPANDER CAN 8B 14DIP
MCP25050T-I/SL IC I/O EXPANDER CAN 8B 14SOIC
MCP25020-E/P IC I/O EXPANDER CAN 8B 14DIP
相關代理商/技術參數
參數描述
MCP25050-I 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O Expander Family
MCP25050I/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O Expander Family
MCP25050-I/P 功能描述:網絡控制器與處理器 IC Mixed signal Expandr RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCP25050-I/P 制造商:Microchip Technology Inc 功能描述:Communication IC
MCP25050I/SL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:CAN I/O Expander Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*