When the device is connected to the I
參數資料
型號： MCP4725A0T-E/CH
廠商： Microchip Technology
文件頁數： 16/50頁
文件大?。?/td> 0K
描述： IC DAC 12BIT W/I2C SOT23A-6
標準包裝： 1
設置時間： 6µs
位數： 12
數據接口： EEPROM，I²C，串行
轉換器數目： 1
電壓電源： 單電源
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： SOT-23-6
供應商設備封裝： SOT-23-6
包裝： 標準包裝
輸出數目和類型： 1 電壓，單極；1 電壓，雙極
采樣率（每秒）： *
產品目錄頁面： 673 (CN2011-ZH PDF)
配用： MCP4725DM-PTPLS-ND - BOARD DAUGHTER PICTAIL MCP4725
其它名稱： MCP4725A0T-E/CHDKR
MCP4725AOT-E/CHDKR
MCP4725AOT-E/CHDKR-ND
2009 Microchip Technology Inc.
DS22039D-page 23
MCP4725
6.0
THEORY OF OPERATION
When the device is connected to the I2C bus line, the
device is working as a slave device. The Master (MCU)
can write/read the DAC input register or EEPROM
using the I2C interface command. The MCP4725
device address contains four fixed bits ( 1100 = device
code) and three address bits (A2, A1, A0). The A2 and
A1 bits are hard-wired during manufacturing, and A0 bit
is determined by the logic state of A0 pin. The A0 pin
can be connected to VDD or VSS, or actively driven by
digital logic levels.
The following sections describe the communication
protocol to send or read the data code and write/read
the EEPROM using the I2C interface. See Section 7.0
6.1
Write Commands
The write commands are used to load the configuration
bits and DAC input code to the DAC register, or to write
to the EEPROM of the device. The write command
types are defined by using three write command type
bits (C2, C1, C0). Table 6-2 shows the write command
types and their functions. There are three command
types for the MCP4725. The four “reserved” commands
in Table 6-2 are for future use. The MCP4725 ignores
the “reserved” commands. Write command protocol
examples are shown in Figure 6-1 and Figure 6-2.
The input data code is coded as shown in Table 6-1.
The MSB of the data is always transmitted first and the
format is unipolar binary.
TABLE 6-1:
INPUT DATA CODING
6.1.1
WRITE COMMAND FOR FAST
MODE (C2 = 0, C1 = 0, C0 = X,
X = DON’T CARE)
The fast write command is used to update the DAC
register. The data in the EEPROM of the device is not
affected by this command. This command updates
Power-Down mode selection bits (PD1 and PD0) and
12 bits of the DAC input code in the DAC register.
Figure 6-1 shows an example of the fast write
command for the MCP4725 device.
6.1.2
WRITE COMMAND FOR DAC INPUT
REGISTER (C2 = 0, C1 = 1, C0 = 0)
In MCP4725, this command performs the same
function as the Fast Mode command in Section 6.1.1
command protocol for the MCP4725.
As shown in Figure 6-2, the D11 - D0 bits in the third
and fourth bytes are DAC input data. The last 4 bits (X,
X, X, X) in the fourth byte are don’t care bits.
The device executes the Master’s write command after
receiving the last byte (4th byte). The Master can send
a STOP bit to terminate the current sequence, or send
a Repeated START bit followed by an address byte. If
the device receives three data bytes continuously after
the 4th byte, it updates from the 2nd to the 4th data
bytes with the last three input data bytes.
The contents of the register are updated at the end of
the 4th byte. The device ignores any partially received
data bytes if the I2C communication with the Master
ends before completing the 4th byte.
6.1.3
WRITE COMMAND FOR DAC INPUT
REGISTER AND EEPROM
(C2 = 0, C1 = 1, C0 = 1)
When the device receives this command, it (a) loads
the configuration and data bits to the DAC register, and
(b) also writes the EEPROM. When the device is
writing the EEPROM, the RDY/BSY bit goes low and
stays low until the EEPROM write operation is
completed. The state of the RDY/BSY bit can be
monitored by a read command. Figure 6-2 shows the
details of the this write command protocol and
Figure 6-3 shows the details of the read command.
Input Code
Nominal Output Voltage
(V)
111111111111
(FFFh)
VDD - 1 LSB
111111111110
(FFEh) VDD - 2 LSB
000000000010
(002h)
2 LSB
000000000001
(001h)
1 LSB
000000000000
(000h)
0
相關PDF資料
PDF描述
MS3120P18-11P CONN RCPT 11POS WALL MNT W/PINS
MCP4716A0T-E/CH IC DAC 10BIT NV EEP I2C SOT-23-6
ICS570ALFT IC MULTIPLIER/ZDB 8-SOIC
VE-22H-MW-F2 CONVERTER MOD DC/DC 52V 100W
PI3B16211AE IC 24-BIT BUS SWITCH 56-TSSOP
相關代理商/技術參數
參數描述
MCP4725A1T-E/CH 功能描述:數模轉換器- DAC Sngl 12-B NV DAC w/ I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4725A1T-E/CH-CUT TAPE 制造商:Microchip 功能描述:MCP4725 Series 1 Ch I2C EEPROM Memory 5.5 V 12-Bit D/A Converter SMT - SOT-23-6
MCP4725A2T-E/CH 功能描述:數模轉換器- DAC Sngl 12-B NV DAC w/ I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4725A2T-E/CH-CUT TAPE 制造商:Microchip 功能描述:MCP4725 Series 1 Ch I2C EEPROM Memory 5.5 V 12-Bit D/A Converter SMT - SOT-23-6
MCP4725A3T-E/CH 功能描述:數模轉換器- DAC Sngl 12-B NV DAC w/ I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*