參數資料
型號： MCZ33970EG
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms
中文描述： 雙計驅動集成電路與改進的阻尼算法
文件頁數： 15/36頁
文件大?。?/td> 430K
代理商： MCZ33970EG
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
33970
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
PE9 (D9) — Pointer Position or Pointer Speed Select bit.
This bit is recognized only if PE11 and PE10 = 1.
0 = Gauge 0 or Gauge 1 Pointer Position
1 = Gauge 0 and Gauge 1 Pointer Speed
PE8 (D8) — Pointer Position Gauge Select bit. Also the
Position 0 of the selected gauge is determined by the PE7
selection. This bit is recognized only if PE11 and PE10 = 1
and PE9 = 0.
0 = Gauge 0 position
1 = Gauge 1 position
PE7 (D7) — Position 0 Location Select bit. This bit
determines the Position 0 of the gauge selected by PE8. RTZ
direction will always be to the position 0.
0 = Position 0 is the most CCW (counterclockwise)
position
1 = Position 0 is the most CW (clockwise) position
PE6 (D6) — This bit must be transmitted as logic [0] for
valid PECCR commands.
PE5 (D5) — Air Core Motor Emulation bit. This bit is
enabled or disabled (acceleration and deceleration is
constant if disabled).
0 = Enable
1 = Disable
PE4 (D4) — Clock Calibration Frequency Selector
0 = Maximum f =1.0 MHz (for 8.0
μ
s calibration pulse)
1 = Nominal f =1.0 MHz (for 8.0
μ
s calibration pulse)
PE3 (D3) — Clock Calibration Enable bit. This bit enables
or disables the clock calibration.
0 = Disable
1 = Enable
PE2 (D2) — Oscillator Adjustment
0 = t
CLU
1 = 0.66 x t
CLU
PE1 (D1) — Gauge 1 Enable bit. This bit enables or
disables the output driver of Gauge 1.
0 = Disable
1 = Enable
PE0 (D0) — Gauge 0 Enable bit. This bit enables or
disables the output driver of Gauge 0.
0 = Disable
1 = Enable
Address 001 — Maximum Velocity Register (VELR)
The Gauge Maximum Velocity Register is used to set a
maximum velocity for each gauge (refer to
Table 8
). Bits
V7:V0 contain a position value from 1– 225 that is
representative of the velocity position value described in
Table 21
, page
24
. The table value becomes the maximum
velocity until it is changed to another value. If a maximum
value is chosen greater than the maximum velocity in the
acceleration table, the maximum table value becomes the
maximum velocity. If the motor is turning at a speed greater
than the new maximum, the motor immediately moves down
the velocity ramp until the speed falls equal to or below it.
Velocity for each motor can be changed simultaneously or
independently by writing V8 and/or V9 to a logic [1]. Bits
V12:V10 must be at logic [0] for valid VELR commands.
The bits in
Table 8
are
write-only
.
V12:V10 (D12:D10) — These bits must be transmitted as
logic [0] for valid VELR commands
V9 (D9) — Gauge 1 Velocity. Specifies whether the
maximum velocity determined in the V7: V0 field will apply to
Gauge 1.
0 = Velocity does not apply to Gauge 1
1 = Velocity applies to Gauge 1
V8 (D8) — Gauge 0 Velocity. Specifies whether the
maximum velocity specified in the V7: V0 field will apply to
Gauge 0.
0 = Velocity does not apply to Gauge 0
1 = Velocity applies to Gauge 0
V7:V0 (D7:D0) — Maximum Velocity. Specifies the
maximum velocity position from
Table 21
. This velocity will
remain the maximum of the intended gauge until changed by
command. Velocities can range from position 1 (00000001)
to position 225 (11111111).
Addresses 010 and 011 — Gauge 0/1 Position Registers
(POS0R, POS1R)
Gauge 0 Position Register (SI Addresses 010) bits
P0 11: P0 0 are written to when communicating the desired
pointer positions, and Gauge 1 Position Register (SI Address
011) bits P1 11: P1 0 are written to when communicating the
desired pointer positions. Commanded positions can range
from 0 to 4095. The D12 bit must be at logic [0] for valid
POS0R and POS1R commands.
Table 8. Maximum Velocity Register (VELR)
Address 001
Bits
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Read
–
–
–
–
–
–
–
–
–
–
–
–
–
Write
0
0
0
V9
V8
V7
V6
V5
V4
V3
V2
V1
V0
相關PDF資料
PDF描述
MCZ33976EG Dual Gauge Driver with Configurable esponse Time
MCZ33977EG Single Gauge Driver
MCZ33989EG System Basis Chip with High-Speed CAN Transceiver
MCZ33990EF Enhanced Class B Serial Transceiver
MCZ33991EG Gauge Driver Integrated Circuit
相關代理商/技術參數
參數描述
MCZ33970EG 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GAUGE DRIVER SPI
MCZ33970EGR2 功能描述:馬達/運動/點火控制器和驅動器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MCZ33972AEK 功能描述:接口 - 專用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MCZ33972AEK/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-up
MCZ33972AEKR2 功能描述:接口 - 專用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*