- 您現在的位置：買賣IC網 > PDF目錄377969 > ML2264 (Fairchild Semiconductor Corporation) 4-Channel High-Speed 8-Bit A/D Converter with T/H (S/H)(具有跟蹤/保持（采樣/保持）電路的四通道8位高速A/D轉換器) PDF資料下載
參數資料
| 型號： | ML2264 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 4-Channel High-Speed 8-Bit A/D Converter with T/H (S/H)(具有跟蹤/保持（采樣/保持）電路的四通道8位高速A/D轉換器) |
| 中文描述： | 4通道高速8位A / D轉換器的T / H（上的S /高）（具有跟蹤/保持（采樣/保持）電路的四通道8位高速的A / D轉換器） |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 307K |
| 代理商： | ML2264 |
ML2264
12
1.6 DYNAMIC PERFORMANCE
1.6.1 Sinusoidal Inputs
Since the ML2264 has an internal sample and hold, the
device can digitize high frequency sinusoids with little or
no signal degradations. Using the Nyquist criteria, the
highest frequency input to the converter could
theoretically be 1/2 the sampling rate (f
S
). Any frequency
components above f
S
/2 will be aliased below f
S
/2. In most
applications, these aliased components cause
unacceptable distortion and must be filtered out of the
input. If the input frequency is too close to f
S
/2, then the
requirements on the anti-alias filter become difficult to
impossible to realize with standard component and
tolerances. In most practical applications, the highest
input frequency has to be limited to 1/3 to 1/4 of f
MAX
in
order to relax the filtering requirements enough to make a
realizable anti-alias filter.
The maximum sampling rate (f
max
) for the ML2264 in the
WR-RD mode, (t
RD
< t
INTL
) can be calculated as follows:
f
t
t
t
t
f
ns
ns
ns
ns
WR
RD
RI
P
max
max
=
+
+
+
=
+
+
+
1
1
190
275
235
300
f
max
= 1.000 MHz
t
WR
= Write Pulse Width
t
RD
= Delay Time between
WR
and
RD
Pulses
t
RI
=
RD
to
INT
Delay
t
P
= Delay Time between Conversions
This permits a maximum sampling rate of 1MHz for the
ML2264. The dynamic performance specifications (SNR,
HD, IMD, and FR) for the ML2264 are all specified at
250kHz, which is approximately 1/4 of the sampling rate, f
S
.
In applications where aliased frequency components are
acceptable and filtering of the input signal is not needed,
or where a filter with a steep amplitude response is
available, the user can apply an input sinusoid higher than
250kHz to the device. Note, however, that as the input
frequency increases above 500kHz, dynamic performance
degradation will occur due to the finite bandwidth of the
internal sample and hold.
The Figure 11 plots are 4096 point FFT’s of the ML2264
converting a 257kHz and a 491kHz, 0 to 4.5V, low
distortion sine wave input. The ML2264 samples and
digitizes at its specified accuracy, dynamic input signals
with frequency components up to the Nyquist frequency
(one-half the sampling rate). The output spectra yields
precise measure-ments of the input signal level, harmonic
components, and signal to noise ratio up to the 8-bit level.
The near ideal signal to noise ratio is maintained
independent of increasing analog input frequencies to
500kHz.
1.6.2 Signal-To-Noise Ratio
Signal-to-noise ratio (SNR) is the measured signal to noise
at the output of the converter. The signal is the rms
magnitude of the fundamental. Noise is the rms sum of all
the nonfundamental signals up to half the sampling
frequency. SNR is dependent on the number of
quantization levels used in the digitization process; the
more the levels, the smaller the quantization noise. The
theoretical SNR for a sine wave is given by
SNR = (6.02N + 1.76) dB
where N is the number of bits. Thus for ideal 8-bit
converter, SNR = 49.92 dB.
1.6.3 HARMONIC DISTORTION
Harmonic distortion is the ratio of the rms sum of
harmonics to the fundamental. Total harmonic distortion
(THD) of the ML2264 is defined as
SNR 49.1dB
HD –58.33dB
V
CC
= V
REF
= 5.0V
T
A
= 25 C
400
200
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
FREQUENCY (kHz)
SNR 48.4dB
HD –62.87dB
V
CC
= V
REF
= 5.0V
T
A
= 25 C
400
200
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
FREQUENCY (kHz)
M
M
a) Output Spectrum with f
IN
= 257kHz, f
S
= 1MHz
b) Output Spectrum with f
IN
= 491kHz, f
S
= 1MHz
Figure 11. Dynamic Performance, Sample and Hold Mode
相關PDF資料 |
PDF描述 |
|---|---|
| ML2280 | Serial I/O 8-Bit A/D Converters(串行輸入/輸出的8位A/D轉換器) |
| ML2283 | Serial I/O 8-Bit A/D Converters(串行輸入/輸出的8位A/D轉換器) |
| ML2281 | Serial I/O 8-Bit A/D Converters with Multiplexer Options(多路轉換器可選的串行輸入/輸出的8位A/D轉換器) |
| ML2282 | Serial I/O 8-Bit A/D Converters with Multiplexer Options(多路轉換器可選的串行輸入/輸出的8位A/D轉換器) |
| ML2284 | Serial I/O 8-Bit A/D Converters with Multiplexer Options(多路轉換器可選的串行輸入/輸出的8位A/D轉換器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML2264BCP | 制造商:Micro Linear 功能描述:Data Acquisition System, 4 Channel, 8 Bit, 24 Pin, Plastic, DIP |
| ML2264CCP | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:4-Channel High-Speed 8-Bit A/D Converter with T/H (S/H) |
| ML2264CCR | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:4-Channel High-Speed 8-Bit A/D Converter with T/H (S/H) |
| ML2264CCS | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:4-Channel High-Speed 8-Bit A/D Converter with T/H (S/H) |
| ML-227 | 制造商:GC Electronics 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。