- 您現在的位置：買賣IC網 > PDF目錄3914 > MM908E625ACEK (Freescale Semiconductor)IC HALF-BRIDGE QUAD 54-SOIC PDF資料下載
參數資料
| 型號： | MM908E625ACEK |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 17/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC HALF-BRIDGE QUAD 54-SOIC |
| 標準包裝： | 26 |
| 應用： | 自動鏡像控制 |
| 核心處理器： | HC08 |
| 程序存儲器類型： | 閃存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 輸入/輸出數： | 13 |
| 電源電壓： | 8 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 包裝： | 管件 |
| 供應商設備封裝： | 54-SOICW-EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
ANALOG DIE I/OS
LIN Physical Layer
The LIN bus pin provides a physical layer for single-wire
communication in automotive applications. The LIN physical
layer is designed to meet the LIN physical layer specification.
The LIN driver is a low side MOSFET with internal current
limitation and thermal shutdown. An internal pull-up resistor
with a serial diode structure is integrated, so no external pull-
up components are required for the application in a slave
node. The fall time from dominant to recessive and the rise
time from recessive to dominant is controlled. The symmetry
between both slew rate controls is guaranteed.
The LIN pin offers high susceptibility immunity level from
external disturbance, guaranteeing communication during
external disturbance.
The LIN transmitter circuitry is enabled by setting the
PSON bit in the System Control Register (SYSCTL). If the
transmitter works in the current limitation region, the LINCL
bit in the System Status Register (SYSSTAT) is set. Due to
excessive power dissipation in the transmitter, software is
advised to monitor this bit and turn the transmitter off
immediately.
TXD PIN
The TXD pin is the MCU interface to control the state of the
LIN transmitter (see Figure 1). When TXD is LOW, LIN output
is low (dominant state). When TXD is HIGH, the LIN output
MOSFET is turned off. The TXD pin has an internal pull-up
current source in order to set the LIN bus in recessive state
in the event, for instance, the microcontroller could not control
it during system power-up or power-down.
RXD PIN
The RXD transceiver pin is the MCU interface, which
reports the state of the LIN bus voltage. LIN HIGH (recessive
state) is reported by a high level on RXD, LIN LOW (dominant
state) by a low level on RXD.
STOP MODE/WAKE-UP FEATURE
During STOP mode operation the transmitter of the
physical layer is disabled. The receiver pin is still active and
able to detect wake-up events on the LIN bus line.
If LIN interrupt is enabled (LINIE bit in the Interrupt Mask
Register is set), a falling edge on the LIN line causes an
interrupt. This interrupt switches on the main voltage
regulator and generates a system wake-up.
Analog Multiplexer/ADOUT Pin
The ADOUT pin is the analog output interface to the ADC
of the MCU. See Figure 12. An analog multiplexer is used to
read seven internal diagnostic analog voltages.
Current Recopy
The analog multiplexer is connected to the four low side
current sense circuits of the half-bridges. These sense
circuits offer a voltage proportional to the current through the
low side MOSFET. High or low resolution is selectable: 5.0 V/
2.5 A or 5.0 V/500 mA, respectively. Refer to Half-Bridge
Analog Input PA1
The analog input PA1 is directly connected to the analog
multiplexer, permitting analog values from the periphery to be
read.
TEMPERATURE SENSOR
The 908E625 includes an on-chip temperature sensor.
This sensor offers a voltage that is proportional to the actual
chip junction temperature.
VSUP PRESCALER
The VSUP prescaler permits the reading or measurement
of the external supply voltage. The output of this voltage is
VSUP/RATIOVSUP.
The different internal diagnostic analog voltages can be
selected with the ADMUX Register.
ANALOG MULTIPLEXER CONFIGURATION
REGISTER (ADMUX)
SS3, SS2, SS1, and SS0—A/D Input Select Bits
These read/write bits select the input to the ADC in the
microcontroller according to Table 7. Reset clears SS3, SS2,
SS1, and SS0 bits.
Register Name and Address: ADMUX - $07
Bits
7
6
5
4
3
2
1
0
Read
0
SS3
SS2
SS1
SS0
Write
Reset
0
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E624ACEW | IC SWITCH TRIPLE MCU/LIN 54-SOIC |
| 06FMN-BMTTR-A-TB | CONN FMN HSNG 6POS STAG REV SMD |
| 046232104103800+ | CONN FFC/FPC 4POS 1MM R/A SMD |
| 046232106103800 | CONN FFC/FPC 6POS 1MM R/A SMD |
| 046232106103800+ | CONN FFC/FPC 6POS 1MM R/A SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。