OPERATIONAL MODES FUNCTIONAL DEVICE OPERAT" />
參數資料
型號： MM908E625ACEK
廠商： Freescale Semiconductor
文件頁數： 9/49頁
文件大?。?/td> 0K
描述： IC HALF-BRIDGE QUAD 54-SOIC
標準包裝： 26
應用： 自動鏡像控制
核心處理器： HC08
程序存儲器類型： 閃存（16 kB）
控制器系列： 908E
RAM 容量： 512 x 8
接口： SCI，SPI
輸入/輸出數： 13
電源電壓： 8 V ~ 18 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤
包裝： 管件
供應商設備封裝： 54-SOICW-EP
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
908E625
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
INTERRUPTS
The 908E625 has seven different interrupt sources as
described in the following paragraphs. The interrupts can be
disabled or enabled via the SPI. After reset all interrupts are
automatically disabled.
LOW VOLTAGE INTERRUPT
The low voltage interrupt (LVI) is related to the external
supply voltage, VSUP. If this voltage falls below the LVI
threshold, it will set the LVI flag. If the low voltage interrupt is
enabled, an interrupt will be initiated.
With LVI the H-Bridges (high side MOSFET only) and the
high side driver are switched off. All other modules are not
influenced by this interrupt.
During STOP mode the LVI circuitry is disabled.
HIGH VOLTAGE INTERRUPT
The high voltage interrupt (HVI) is related to the external
supply voltage, VSUP. If this voltage rises above the HVI
threshold, it will set the HVI flag. If the high voltage interrupt
is enabled, an interrupt will be initiated.
With HVI the H-Bridges (high side MOSFET only) and the
high side driver are switched off. All other modules are not
influenced by this interrupt.
During STOP mode the HVI circuitry is disabled.
HIGH TEMPERATURE INTERRUPT
The high temperature interrupt (HTI) is generated by the
on-chip temperature sensors. If the chip temperature is
above the HTI threshold, the HTI flag will be set. If the high
temperature interrupt is enabled, an interrupt will be initiated.
During STOP mode the HTI circuitry is disabled.
AUTONOMOUS WATCHDOG INTERRUPT (AWD)
Refer to Autonomous Watchdog Autonomous Watchdog
LIN INTERRUPT
If the LINIE bit is set, a falling edge on the LIN pin will
generate an interrupt. During STOP mode this interrupt will
initiate a system wake-up.
HALL-EFFECT SENSOR INPUT PIN INTERRUPT
If the PHIE bit is set, the enabled Hall-effect sensor input
pins H1:H3 can generate an interrupt if a current above the
threshold is detected. During Stop mode this interrupt,
combined with the cyclic wake-up feature of the AWD, can
wake up the system. Refer to pin
OVER-CURRENT INTERRUPT
If an over-current condition on a half-bridge occurs, the
high side or the HVDD output is detected and the OCIE bit is
set and an interrupt generated.
SYSTEM WAKE-UP
System wake-up can be initiated by any of four events:
A falling edge on the LIN pin
A wake-up signal from the AWD
A Logic [1] at Hall-effect sensor input pin during cyclic
check via AWD
An LVR condition
If one of these wake-up events occurs and the interrupt
mask bit for this event is set, the interrupt will wake-up the
microcontroller as well as the main voltage regulator (MREG)
相關PDF資料
PDF描述
MM908E624ACEW IC SWITCH TRIPLE MCU/LIN 54-SOIC
06FMN-BMTTR-A-TB CONN FMN HSNG 6POS STAG REV SMD
046232104103800+ CONN FFC/FPC 4POS 1MM R/A SMD
046232106103800 CONN FFC/FPC 6POS 1MM R/A SMD
046232106103800+ CONN FFC/FPC 6POS 1MM R/A SMD
相關代理商/技術參數
參數描述
MM908E625ACPEK 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*