- 您現在的位置：買賣IC網 > PDF目錄3914 > MM908E625ACEK (Freescale Semiconductor)IC HALF-BRIDGE QUAD 54-SOIC PDF資料下載
參數資料
| 型號： | MM908E625ACEK |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 28/49頁 |
| 文件大小： | 0K |
| 描述： | IC HALF-BRIDGE QUAD 54-SOIC |
| 標準包裝： | 26 |
| 應用： | 自動鏡像控制 |
| 核心處理器： | HC08 |
| 程序存儲器類型： | 閃存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 輸入/輸出數： | 13 |
| 電源電壓： | 8 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 包裝： | 管件 |
| 供應商設備封裝： | 54-SOICW-EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
34
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
H-Bridge Current Limitation Selection Bits (CLS2:CLS0)
These read/write bits select the current limitation value
according to Figure 10. Reset clears the CLS2:CLS0 bits.
HIGH SIDE DRIVER
The high side output is a low-resistive high side switch
targeted for driving lamps. The high side is protected against
over-temperature. To limit the high inrush current of bulbs,
over-current protection circuitry is used to limit the current.
The output is enabled with bit PSON in the system control
register and can be switched on/off with bit HS_ON in the
power output register. Figure 21 depicts the high-side switch
circuitry and connection to external lamp.
HIGH-SIDE OVER-VOLTAGE/UNDER-VOLTAGE
PROTECTION
The high side output pin, HS, is protected against under-
voltage/over-voltage conditions. This protection is done by
the low and high voltage interrupt circuitry. If one of these
flags (LVF, HVF) is set, the output is disabled.
The over-voltage/under-voltage status flags are cleared
and the output re-enabled by writing a Logic [1] to the LVF/
HVF flags in the interrupt flag register or by reset. Clearing
this flag is useless as long as a high or low voltage condition
is present.
Figure 21. High Side Circuitry
HIGH SIDE OVER-TEMPERATURE PROTECTION
The high side output provides an over-temperature pre-
warning with the HTF in the interrupt flag register. In order to
protect the output against over-temperature, the high-
temperature reset must be enabled. If this value is reached,
the part generates a reset and disables all power outputs.
HIGH-SIDE OVER-CURRENT PROTECTION
The high side output is protected against over-current. In
the event over-current limit is or was reached, the output
automatically switches off and the over-current flag is set.
Due to the high inrush current of bulbs, a special feature of
the 908E625 prevents an over-current shutdown during this
inrush. If an PWM frequency is supplied to the FGEN output
during the switching on of a bulb, the inrush current is limited
to the over-current shutdown limit. This means if the current
reaches the over-current shutdown, the high side will be
switched off, but each rising edge on the FGEN input will
enable the driver again.
To distinguish between a shutdown due to an inrush
current or a real shutdown, the software must check if the
over-current status flag (HS_OCF) in the System Status
Register is set beyond a certain period of time. The over-
current status flag is cleared by writing a Logic [1] to the
HS_OCF in the System Status Register, see Figure 22.
Table 10. H-Bridge Current Limitation Value Selection
Bits
CLS2
CLS1
CLS0
Current Limit
000
No Limit
001
010
011
55 mA (typ)
100
260 mA (typ)
101
370 mA (typ)
110
550 mA (typ)
111
740 mA (typ)
VSUP
HS
High Side Driver
Charge Pump,
OVer-current Protection,
Inrush Current Limiter
Control
On/Off
Current
Limit
Status
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E624ACEW | IC SWITCH TRIPLE MCU/LIN 54-SOIC |
| 06FMN-BMTTR-A-TB | CONN FMN HSNG 6POS STAG REV SMD |
| 046232104103800+ | CONN FFC/FPC 4POS 1MM R/A SMD |
| 046232106103800 | CONN FFC/FPC 6POS 1MM R/A SMD |
| 046232106103800+ | CONN FFC/FPC 6POS 1MM R/A SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。