- 您現在的位置：買賣IC網 > PDF目錄359188 > MPC18730EP (飛思卡爾半導體(中國)有限公司) Power Management IC with Five Regulated Outputs Programmed Through 3 Wire Serial Interface PDF資料下載
參數資料
| 型號： | MPC18730EP |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Power Management IC with Five Regulated Outputs Programmed Through 3 Wire Serial Interface |
| 中文描述： | 與電源管理IC，通過3線串行接口編程五穩壓輸出 |
| 文件頁數： | 15/35頁 |
| 文件大小： | 617K |
| 代理商： | MPC18730EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
18730
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
DUTY CONTROL PINS (DMAX1, DMAX2)
Connected external voltage to this pin via capacitance can
control the duty of DC/DC converter switching. Use of the pin
for this is not recommended.
REFERENCE FEEDBACK PINS (EAOUT1, EAOUT2)
Output node of internal error amp. for DC/DC converter 1
and 2. Used for phase compensation.
INPUT MINUS PINS (EAIN1, EAIN2)
Minus input of internal error amp. for DC/DC converter 1
and 2. Used for phase compensation.
CHARGE PUMP CAPACITOR PIN (CH_PUMP)
In case of use higher voltage than VGATE externally,
connect capacitance and diodes between VGATE. The
charge pump structure can output VGATE + VB - 2 x VF
voltage. There is no meaning for Ni-MH or dry cell battery,
because the VB voltage is almost same as 2 x VF voltage.
Recommend to use for Li-Ion battery use.
GATE VOLTAGE PIN (VGATE)
Output pin of boost converter for gate drive voltage. The
output voltage is decided by VGSEL input.
SWITCHING FOR GATE VOLTAGE PIN (SWGATE)
Switching pin for VGATE boost converter. Connect to
external inductance.
BATTERY VOLTAGE PIN (VBATT)
Power supply input that connects to Ni-MH or Dry cell or
Li-Ion battery.
VGATE SELECT PINS (VGATESEL1, VGATESEL2)
VGATE output voltage is decided with these two bits input.
VOLTAGE INPUT FOR POWER SWITCH 2 PIN
(VO2_SENSE_IN)
Input of VOUT2 output via power switch. Connect to
VO2_SENSE pin externally.
STEP DOWN FET GATE DRIVE PINS (HG, LG)
Gate drive output pins for external FETs to use DC/DC
converter 2 as Buck / Boost converter.
GATE SWITCH PIN (VGATE_EXT)
Gate drive output pin for external low side switch. It can be
used for power switch turning On/OFF for remote controller
part.
REGULATOR CONTROL PINS (SREGC1, SREGC2,
SREGC3)
Feed back pin for each series regulators. This pin voltage
is compared with internal reference voltage. Input the feed
back voltage that divided SREGO voltage by resistances.
REGULATOR OUTPUT PINS (SREGO1, SREGO2,
SREGO3)
Series regulator output pins. All output voltages can be
variable with internal DAC via serial I/F.
REGULATOR INPUT PINS (SREGI1, SREGI2,
SREGI3)
Series regulator power input pins. To be connected to
battery voltage in general.
GROUND PIN (GND)
Ground pin for logic and analog circuit portion (not power
portion). Recommend to connect to clean ground which
separated with power ground line.
REFERENCE VOLTAGE PIN (VREF)
Output of internal reference voltage. It can be used
externally. Output current capacity is less than 300
μ
A.
DATA INPUT PIN (DATA)
Serial data input pin for the serial interface. The last 12 bits
received before the strobe signal’s low to high transition are
latched.
STROBE PIN (STRB)
Strobe signal input pin for serial interface. It latches the 12
bits of data input to the internal control registers.
SERIAL CLOCK PIN (SCKIN)
Clock input pin for serial interface. Input data are taken in
to I/F with this clock.
WATCH DOG TIMER PIN (WATCHDOG)
Watch dog timer prevent unstable wake up (flips between
wake-up and failure). If there is no ‘CLEAR’ input after any
WAKEnB input before this WATCHDOG is expired, this
device moves to ‘SLEEP’ mode to prevent wake failure
hanging-up situation.
SEQUENCE SELECT PIN (SEQ_SELECT)
Select judgement Reset channel for wake-up complete
with this input. If this input level is V_STDBY voltage, this
device judges the wake-up completion with Reset2 (DC/
DC2). If it is Ground, judge with Reset1 (DC/DC1). See
Table 7, on page 13
.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC5200B | SDRAM/DDR Memory Controller |
| MPC5200 | Hardware Specifications |
| MPC5534 | Microcontroller |
| MPC7447A | PowerPC microprocessor |
| MPC7447ANXPNS | PowerPC microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC18730EP | 制造商:Freescale Semiconductor 功能描述:IC POWER MANAG PROG 121MA 64QFN |
| MPC18730EP/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Power Management IC with Five Power Management IC with Five Power Management IC with Five Power Management IC with Five |
| MPC18730EPR2 | 功能描述:板上安裝壓力/力傳感器 POWER MGT IC RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPC18A26VMEL | 制造商:Motorola Inc 功能描述: |
| MPC190VMB | 制造商:Freescale Semiconductor 功能描述:IC SECURITY PROCESSOR 252-MAPBGA |
發布緊急采購，3分鐘左右您將得到回復。