參數資料
型號： MPC8245TZU300D
廠商： Freescale Semiconductor
文件頁數： 17/68頁
文件大?。?/td> 0K
描述： IC MPU 32BIT 300MHZ 352-TBGA
標準包裝： 24
系列： MPC82xx
處理器類型： 32-位 MPC82xx PowerQUICC II
速度： 300MHz
電壓： 1.8V
安裝類型： 表面貼裝
封裝/外殼： 352-LBGA
供應商設備封裝： 352-TBGA（35x35）
包裝： 托盤
MPC8245 Integrated Processor Hardware Specifications, Rev. 10
24
Freescale Semiconductor
Electrical and Thermal Characteristics
Figure 14 provides the AC test load for the MPC8245.
Figure 14. AC Test Load for the MPC8245
14b
sys_logic_clk to output high impedance (for all others)
—
4.0
ns
2
Notes:
1. All PCI signals are measured from GVDD/2 of the rising edge of PCI_SYNC_IN to 0.285 × OVDD or 0.615 × OVDD of the
signal in question for 3.3 V PCI signaling levels. See Figure 12.
2. All memory and related interface output signal specifications are specified from the VM = 1.4 V of the rising edge of the
memory bus clock, sys_logic_clk to the TTL level (0.8 or 2.0 V) of the signal in question. sys_logic_clk is the same as
PCI_SYNC_IN in 1:1 mode, but is twice the frequency in 2:1 mode (processor/memory bus clock rising edges occur on every
rising and falling edge of PCI_SYNC_IN). See Figure 11.
3. PCI bused signals are composed of the following signals: LOCK, IRDY, C/BE[3:0], PAR, TRDY, FRAME, STOP, DEVSEL,
PERR, SERR, AD[31:0], REQ[4:0], GNT[4:0], IDSEL, and INTA.
4. To meet minimum output hold specifications relative to PCI_SYNC_IN for both 33- and 66-MHz PCI systems, the MPC8245
has a programmable output hold delay for PCI signals (the PCI_SYNC_IN to output valid timing is also affected). The initial
value of the output hold delay is determined by the values on the MCP and CKE reset configuration signals; the values on
these two signals are inverted and stored as the initial settings of PCI_HOLD_DEL = PMCR2[5, 4] (power management
configuration register 2 <0x72>), respectively. Since MCP and CKE have internal pull-up resistors, the default value of
PCI_HOLD_DEL after reset is 0b00. Further output hold delay values are available by programming the PCI_HOLD_DEL
value of the PMCR2 configuration register. Figure 15 shows the PCI_HOLD_DEL effect on output valid and hold times.
Table 11. Output AC Timing Specifications (continued)
Num
Characteristic
Min
Max
Unit
Notes
Output
Z0 = 50 Ω
OVDD/2 for PCI
RL = 50 Ω
Output Measurements are Made at the Device Pin
GVDD/2 for Memory
相關PDF資料
PDF描述
MPC8245TVV300D IC MPU 32BIT 300MHZ PPC 352-TBGA
MPC8378VRANGA MPU POWERQUICC II 800MHZ 689PBGA
MPC8377VRANGA MPU POWERQUICC II 800MHZ 689PBGA
MPC866TVR100A IC MPU POWERQUICC 100MHZ 357PBGA
IDT709159L7BF IC SRAM 72KBIT 7NS 100FBGA
相關代理商/技術參數
參數描述
MPC8245TZU333D 功能描述:微處理器 - MPU 333MHz 632.7MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC8245TZU350D 功能描述:微處理器 - MPU 350MHz 665MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC8247 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC8272 PowerQUICC II Family Hardware Specifications
MPC8247CVR 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC8272 PowerQUICC II Family Hardware Specifications
MPC8247CVRB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC II⑩ Family Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*