參數(shù)資料
型號: MS27C801
廠商: 意法半導體
英文描述: 8 Mbit (1Mb x 8) UV EPROM and OTP EPROM
中文描述: 8兆(1兆× 8)紫外線存儲器和OTP存儲器
文件頁數(shù): 10/16頁
文件大?。?/td> 158K
代理商: MS27C801
M27C801
10/16
Electronic Signature
The Electronic Signature (ES) mode allows the
reading out of a binary code from an EPROM that
will identify its manufacturer and type. This mode
is intended for use by programming equipment to
automatically match the device to be programmed
with its corresponding programming algorithm.
The ES mode is functional in the 25°C ± 5°C am-
bient temperature range that is required when pro-
gramming the M27C801. To activate the ES
mode, the programming equipment must force
11.5V to 12.5V on address line A9 of the
M27C801. Two identifier bytes may then be se-
quenced from the device outputs by toggling ad-
dress line A0 from V
IL
to V
IH
. All other address
lines must be held at V
IL
during Electronic Signa-
ture mode. Byte 0 (A0 = V
IL
) represents the man-
ufacturer code and byte 1 (A0 = V
IH
) the device
identifier code. For the STMicroelectronics
M27C801, these two identifier bytes are given in
Table 4 and can be read-out on outputs Q7 to Q0.
ERASURE OPERATION (applies to UV EPROM)
The erasure characteristics of the M27C801 is
such that erasure begins when the cells are ex-
posed to light with wavelengths shorter than ap-
proximately 4000 . It should be noted that
sunlight and some type of fluorescent lamps have
wavelengths in the 3000-4000 range.
Research shows that constant exposure to room
level fluorescent lighting could erase a typical
M27C801 in about 3 years, while it would take ap-
proximately 1 week to cause erasure when ex-
posed to direct sunlight. If the M27C801 is to be
exposed to these types of lighting conditions for
extended periods of time, it is suggested that
opaque labels be put over the M27C801 window to
prevent unintentional erasure. The recommended
erasure procedure for the M27C801 is exposure to
short wave ultraviolet light which has wavelength
2537 . The integrated dose (i.e. UV intensity x
exposure time) for erasure should be a minimum
of 30 W-sec/cm
2
. The erasure time with this dos-
age is approximately 30 to 40 minutes using an ul-
traviolet lamp with 12000 μW/cm
2
power rating.
The M27C801 should be placed within 2.5 cm (1
inch) of the lamp tubes during the erasure. Some
lamps have a filter on their tubes which should be
removed before erasure.
相關PDF資料
PDF描述
MSC2712YT1 General Purpose Amplifier Transistor
MSC2712GT1 General Purpose Amplifier Transistors(通用放大晶體管)
MSD42SWT1 NPN Silicon General Purpose High Voltage Transistor
MSD42SWT1G NPN Silicon General Purpose High Voltage Transistor
MSOP8 Motor Driver IC; No. of Drivers:2; Output Current Max:3A; Package/Case:44-PLCC; Leaded Process Compatible:Yes; Output Current Min:-3A; Peak Reflow Compatible (260 C):Yes; Mounting Type:Surface Mount; Voltage Rating:7V RoHS Compliant: Yes
相關代理商/技術參數(shù)
參數(shù)描述
MS27-R 制造商:TURCK Inc 功能描述:M0508412
MS28005-3 制造商: 功能描述: 制造商:MILITARY STANDARDS PROMUL 功能描述: 制造商:undefined 功能描述:
MS28034-3 制造商:Contact Us 功能描述:
MS280536 制造商:Talley 功能描述:MS280536
MS281 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Power Film Resistors