參數資料
型號: MSP430F1101IPWR
廠商: TEXAS INSTRUMENTS INC
元件分類: 微控制器/微處理器
英文描述: 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
封裝: PLASTIC, TSSOP-20
文件頁數: 18/43頁
文件大?。?/td> 869K
代理商: MSP430F1101IPWR
MSP430C11x1, MSP430F11x1A
MIXED SIGNAL MICROCONTROLLER
SLAS241I SEPTEMBER 1999 REVISED DECEMBER 2008
25
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (continued)
flash memory
PARAMETER
TEST
CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VCC(PGM/
ERASE)
Program and erase supply voltage
2.7
3.6
V
fFTG
Flash Timing Generator frequency
257
476
kHz
IPGM
Supply current from VCC during program
2.7 V/ 3.6 V
3
5
mA
IERASE
Supply current from VCC during erase
2.7 V/ 3.6 V
3
7
mA
tCPT
Cumulative program time
See Note 1
2.7 V/ 3.6 V
4
ms
tCMErase
Cumulative mass erase time
See Note 2
2.7 V/ 3.6 V
200
ms
Program/erase endurance
104
105
cycles
tRetention
Data retention duration
TJ = 25°C
100
years
tWord
Word or byte program time
35
tBlock, 0
Block program time for first byte or word
30
tBlock, 1-63
Block program time for each additional byte or word
See Note 3
21
t
tBlock, End
Block program end-sequence wait time
See Note 3
6
tFTG
tMass Erase
Mass erase time
5297
tSeg Erase
Segment erase time
4819
NOTES:
1. The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
2. The mass erase duration generated by the flash timing generator is at least 11.1ms ( = 5297x1/fFTG,max = 5297x1/476kHz). To
achieve the required cumulative mass erase time the Flash Controller’s mass erase operation can be repeated until this time is met.
(A worst case minimum of 19 cycles are required).
3. These values are hardwired into the Flash Controller’s state machine (tFTG = 1/fFTG).
JTAG interface
PARAMETER
TEST
CONDITIONS
VCC
MIN
TYP
MAX
UNIT
f
TCK input frequency
see Note 1
2.2 V
0
5
MHz
fTCK
TCK input frequency
see Note 1
3 V
0
10
MHz
RInternal
Internal pulldown resistance on TEST
see Note 2
2.2 V/ 3 V
25
60
90
k
Ω
NOTES:
1. fTCK may be restricted to meet the timing requirements of the module selected.
2. TEST pull-down resistor implemented in all versions.
JTAG fuse (see Note 1)
PARAMETER
TEST
CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VCC(FB)
Supply voltage during fuse-blow condition
TA = 25°C
2.5
V
Voltage level on TEST for fuse blow (’C11x1)
3.5
3.9
V
VFB
Voltage level on TEST for fuse blow (’F11x1A)
6
7
V
IFB
Supply current into TEST during fuse blow
100
mA
tFB
Time to blow fuse
1
ms
NOTES:
1. Once the fuse is blown, no further access to the MSP430 JTAG/Test and emulation (F versions only) features is possible. The JTAG
block is switched to bypass mode.
相關PDF資料
PDF描述
MSP430F1121IDWR 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
MSP430C1101 16-BIT, MROM, 8 MHz, RISC MICROCONTROLLER, PQCC24
MSP430F1121AIDW 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
MSP430F1121IPW 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
MSP430F1132IDWR 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
MSP430F110AIDW 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:
MSP430F110AIDWR 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430F110AIPW 制造商:Rochester Electronics LLC 功能描述:16-BIT ULTRA-LOW-POWER MICROCONTROLLER, 1KB FLASH, 128B RAM - Bulk
MSP430F110AIPWR 制造商:TI 制造商全稱:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430F110IDW 功能描述:IC MCU 16BIT 1KB FLASH 20-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MSP430x1xx 產品培訓模塊:8-bit PIC® Microcontroller Portfolio 標準包裝:91 系列:PIC® XLP™ mTouch™ 16F 核心處理器:PIC 芯體尺寸:8-位 速度:32MHz 連通性:I²C,LIN,SPI,UART/USART 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:11 程序存儲器容量:14KB(8K x 14) 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:16-VQFN 裸露焊盤 包裝:管件