- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8920B (Mitel Networks Corporation) ST-BUS Parallel Access Circuit(串行通信總線（ST-Bus）并行存取電路（在ST總線和并行系統間提供一個簡單接口）) PDF資料下載
參數資料
| 型號： | MT8920B |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | ST-BUS Parallel Access Circuit(串行通信總線（ST-Bus）并行存取電路（在ST總線和并行系統間提供一個簡單接口）) |
| 中文描述： | 意法半導體總線并行訪問電路（串行通信總線（圣總線）并行存取電路（在圣總線和并行系統間提供一個簡單接口）） |
| 文件頁數： | 3/29頁 |
| 文件大?。?/td> | 215K |
| 代理商： | MT8920B |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
CMOS
MT8920B
3-5
Pin Descriptions pertain to all modes unless otherwise stated.
Table 1. STPA Modes of Operation
13
A5
Address Bit A5 (Mode 1).
This input is used to extend the address range of the STPA. A5
selects internal registers when high and Tx/Rx RAM’s when low.
A5
Address Bit A5 (Mode 2).
This input is used to extend the address range of the STPA. A5
selects Tx0/Rx0 RAM’s when low and Tx1/Rx0 RAM’s when high.
STCH
Start of Channel (Mode 3).
This signal is a low going pulse which indicates the start of an
ST-BUS channel. The pulse is four bits wide and begins at the start of each valid channel.
14
V
SS
D0-D7
Bidirectional Data Bus.
This bus is used to transfer data to or from the STPA during a write
or read operation.
Ground.
15-22
23
STo0
ST-BUS Output 0.
This output supplies the output ST-BUS 2048 kbit/s serial data stream from
Tx0 two-port RAM.
24
STo1
ST-BUS Output 1.
In modes 1 and 2 this output supplies the output ST-BUS 2048 kbit/s serial
data stream from Tx1 two-port RAM. In mode 3, information arriving at STi0 is output here with
one frame delay.
25
IRQ
Interrupt Request (Mode 1).
This open drain output, when low, indicates when an interrupt
condition has been raised within the STPA.
24/32
24 Channel/32 Channel Select (Mode 2,3).
This input is used to select the channel
configuration in modes 2 and 3. A low applied to this pin will select a 24 (T1) channel mode
while a high will select a 32 (CEPT) channel mode.
26
DTACK
Data Transfer Acknowledge (Mode 1).
This open drain output is supplied by the STPA to
acknowledge the completion of data transfers back to the
μ
P. On a read of the STPA, DTACK
low indicates that the STPA has put valid data on the data bus. On a write, DTACK low
indicates that the STPA has completed latching the
μ
P’s data from the data bus.
BUSY
BUSY (Mode 2).
This open drain output signals that the controller and the ST-BUS are
accessing the same location in the dual-port RAM’s. It is intended to delay the controller
access until after the ST-BUS completes its access.
DCS
Delayed Chip Select (Mode 3).
This low going pulse, which is four bit cells long, is active
during the last half of a valid channel. This signal is used to daisy-chain together two STPA’s in
mode 3 that are accessing devices on the same parallel data bus.
27
MMS
Master Mode Select (Reset).
This Schmitt trigger input selects between either mode 1 (MMS
= 1), or modes 2and 3 (MMS = 0). If MMS is pulsed low in Mode 1 operation the control and
interrupt registers will be reset. (Refer to Table 1.) During power-up, the time constant of the
reset circuit (see Fig. 8) must be a minimum of five times the rise time of the power supply.
28
V
DD
Power Supply Input.
(+5V).
Mode
MMS
MS1
Mode of
Operation
μ
P
Peripheral
Mode
Function
1
1
N/A
The STPA provides parallel-to-serial and serial-to-parallel conversions through a
68000-type interface. Two Tx RAMs and one Rx RAM are available along with full
interrupt capability. 32 channel or 24 channel support is available. Control Register 1, bit
D
5
(RAMCON) = 0 for 32 channel operation and D
5
(RAMCON)= 1 for 24 channel
operation.
The STPA provides a fast access interface to Tx0, Tx1 and Rx0 RAMs. This mode is
intended for full parallel support of 24 channel T1/ESF trunks and 32 channel CEPT
trunks. Input 24/32 (pin 25) = 0 for 24 channel operation, input 24/32 (pin 25) = 1 for 32
channel operation.
The STPA will synchronously drive the parallel bus using the address generator and
provide all data transfer signals. This mode is intended to support 24 or 32 channel
devices in the absence of a parallel bus controller. Input 24/32 (pin 25) = 0 for 24 channel
operation, input 24/32 (pin 25) = 1 for 32 channel operation.
2
0
1
Fast RAM
Mode
3
0
0
Bus
Controller
Mode
Pin Description (continued)
Pin #
Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| MT8924-1 | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924AE | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924AS | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924 | PCM Conference Circuit (PCC) Preliminary Information |
| MT8930B | () |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8920B-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit |
| MT8920BC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit |
| MT8920BE | 制造商:Mitel Networks Corporation 功能描述:COMMUNICATIONS INTERFACE, 28 Pin, Plastic, DIP |
| MT8920BE1 | 制造商:Zarlink Semiconductor Inc 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PDIP - Rail/Tube 制造商:Microsemi 功能描述:Microsemi MT8920BE1 Interface Misc |
| MT8920BP | 制造商:Microsemi Corporation 功能描述: 制造商:MITEL 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。