參數資料
型號: MT9080B
廠商: Mitel Networks Corporation
英文描述: SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
中文描述: SMX -開關矩陣模塊(用于消費類轉換應用的開關矩陣模塊)
文件頁數: 3/25頁
文件大?。?/td> 123K
代理商: MT9080B
CMOS
MT9080B
2-103
28
CS
Chip Select.
Active Low input. Selects the device for microport access in connect memory,
data memory, external and shift register modes. Tying CS high will disable output data
drivers (D0-D15o) in all modes except connect memory and shift register modes.
29
DS
Data Strobe.
Active low input. Indicates to the SMX that valid data is present on the
microport data bus during a write operation or that the SMX must output data on a read
operation.
In Connect Memory modes, a low level applied to this input during a write operation indicates
to the SMX that valid data is present on the microport data bus. During a read operation the
low going signal indicates to the SMX that it must output data on the microport data bus.
In Data Memory and External modes, when DS is high, the output data bus D0o-D15o will be
disabled. The input data bus D0i-D15i is not affected.
The DS input has no effect on the input and output busses in Counter or Shift Register
modes.
30
R/W
Read/Write Enable.
Data is written into the device when R/W is low and read from it when it
is high. This control input is disabled in data memory and shift register modes. It should be
tied to V
SS
or V
DD
in these modes. In counter and external modes, the state of R/W pin is
clocked in with the rising edge of CK. The actual read or write operation will be implemented
on the next rising clock edge.
31
DTA
Data Transfer Acknowledge.
Open drain output which is pulled low to acknowledge
completion of microport data transfer. On a read of the SMX, DTA low indicates that the SMX
has put valid data on the data bus. On a write, DTA low indicates that the SMX has
completed latching the data in.
32
NC
No Connection.
33
V
SS
NC
Ground.
34
No Connection.
35
ODE
Output Data Enable.
Control input which enables the output data bus. Pulling this input low
will place the data bus in a high impedance state. The level on this pin is latched by a rising
edge of CK. The output drivers will be enabled or disabled with the rising edge in the next
timeslot (see Fig. 24 for applicable timing in different modes).
36
ME
Message Enable.
When tied high the data latched in on the address bus is clocked out on
D0o-D15o. When ME is tied low, the contents of the addressed memory location will be
output on the bus. The level on this pin is latched in with the rising edge of the clock. The
actual mode change is implemented on the rising edge in the next timeslot. Refer to Figures
25 and 26 for more timing information.
37
Mx
Mode X.
One of three inputs which permit the selection of different operating modes for the
device. Refer to Table 1 for description of various modes.
38
My
Mode Y.
See description for pin 37.
39
Mz
Mode Z.
See description for pin 37.
40
NC
No Connection.
41, 42
IC
Internal Connection.
Leave open for normal operation.
43
V
SS
V
DD
NC
Ground.
44
Supply Voltage. +5V.
45
No Connection.
Pin Description
Pin #
Name
Description
相關PDF資料
PDF描述
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
MT90812 Integrated Digital Switch (IDX)(集成數字開關)
MT90840AK Distributed Hyperchannel Switch
MT90840AP Distributed Hyperchannel Switch
MT9085B PAC - Parallel Access Circuit(并行存取電路)
相關代理商/技術參數
參數描述
MT9080BP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS SMX - Switch Matrix Module
MT9081 制造商:MARKTECH 制造商全稱:Marktech Corporate 功能描述:3 Leaded Tri-State LED Lamps
MT90810 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Flexible MVIP Interface Circuit
MT90810AK 制造商:Microsemi Corporation 功能描述:
MT90812 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Integrated Digital Switch (IDX)