- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9160 (Mitel Networks Corporation) ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) PDF資料下載
參數資料
| 型號： | MT9160 |
| 廠商： | Mitel Networks Corporation |
| 元件分類： | Codec |
| 英文描述： | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| 中文描述： | ISO2 - 5伏的CMOS多精選編解碼器（MFC）中 |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 402K |
| 代理商： | MT9160 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Preliminary Information
MT9160
7-89
DrGain
When high, the receiver driver gain is set to -6 dB, with sidetone.
When low, the receiver driver gain is set to 0 dB, with no sidetone.
Path Control
ADDRESS = 02h WRITE/READ VERIFY
Power Reset Value
XX00 0000
7
6
5
4
3
2
1
0
-
-
-
-
-
-
DrGain
-
PDFDI
PDDR
When high, the FDI PLA and the Filter/Codec are powered down. When low, the FDI is active (default).
When high, the ear driver and Filter/Codec are powered down. In addition, in ST-BUS mode, the selected output
channel is tri-stated. In SSI mode the PCM output code will be -zero code during the valid strobe period. The output will
be tri-stated outside of the valid strobe and for the whole frame if no strobe is supplied. When low, the driver and Filter/
Codec are active if PDFDI is low (default).
When high, a software reset occurs performing the same function as the hardware reset (PWRST) except that the
microport is not affected. A software reset can be removed only by writing this bit low or by a PWRST. When low, the
reset condition is removed.
When high the transmit PCM stream is interrupted and replaced with quiet code; thus forcing the output code into a
mute state (only the output code is muted, the transmit microphone and transmit Filter/Codec are still functional). When
low the full transmit path functions normally (default).
When high the received PCM stream is interrupted and replaced with quiet code; thus forcing the receive path into a
mute state. When low the full receive path functions normally (default).
When high, the transmit B2 channel is functional in ST-BUS mode. When low, the transmit B1 channel is functional in
ST-BUS mode. Not used in SSI mode.
When high, the receive B2 channel is functional in ST-BUS mode. When low, the receive B1 channel is functional in
ST-BUS mode. Not used in SSI mode.
Rst
TxMute
RxMute
TxBsel
RxBsel
Control Register 1
ADDRESS = 03h WRITE/READ VERIFY
Power Reset Value
0000 0000
7
6
5
4
3
2
1
0
PDFDI PDDR
TxBsel RxBsel
Rst
_
TxMute RxMute
Note: Bits marked "-" are reserved bits and should be written with logic "0"
相關PDF資料 |
PDF描述 |
|---|---|
| MT9160AE | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT9160AS | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT9160BN | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
| MT91610 | Programmable Ringing SLIC(可編程振鈴用戶線路接口電路（帶一個外部驅動器）) |
| MT9161B | ISO2-CMOS 5 Volt Multi-Featured Codec (MFC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT91600 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Programmable SLIC |
| MT91600AN | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Programmable SLIC |
| MT91600AN1 | 制造商:Microsemi Corporation 功能描述:SLIC 1CH 55DB 32MA 5V 28SSOP - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:SLIC 1CH 55DB 32MA 5V 28SSOP - Rail/Tube |
| MT91600ANR | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Programmable SLIC |
| MT91600ANR1 | 制造商:Microsemi Corporation 功能描述:SLIC 1CH 55DB 32MA 5V 28SSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。