- 您現在的位置：買賣IC網 > PDF目錄359238 > MULTILINK08UM MON08 Multilink Hardware Manual PDF資料下載
參數資料
| 型號： | MULTILINK08UM |
| 英文描述： | MON08 Multilink Hardware Manual |
| 中文描述： | 的MON08多重硬件手冊 |
| 文件頁數： | 40/52頁 |
| 文件大?。?/td> | 517K |
| 代理商： | MULTILINK08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
40
MON08 Multilink User Manual
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
power supply on and off. The use will also be prompted to turn power
on and off to reset the target processor, as the PC doesn’t have control
of the target reset. Turning off the power supply is necessary mainly to
be able to pass the initial security mode check and access the flash on
the processor. A simple reset is not enough; to pass the security check,
you must first force the processor to encounter a POR (power-on reset)
which requires that the processor’s voltage dip below 0.1v. Once
security has been passed, resetting the device or re-entering the
software should be easier. This configuration can be specified at startup
in the software by using the
NODTR
command-line parameter;
otherwise the software will remember the hardware configuration from
session to session. The Class III selection also applies to use of the ICS
board with the two-pin blank part programming connector.
Class IV
Custom Board (no ICS) with MON08 serial port circuitry and
additional auto-reset circuit built in. In this configuration, the ICS
board is not used at all. The user must provide a serial port connection
from the PC and all hardware configuration necessary to force the
processor into MON08 mode upon reset. In addition, the user must
include an extra circuit which allows the reset line of the processor to
be driven low from the DTR line of the serial port connector (Pin 4 on a
DB9). The following diagram shows the additional connection needed
to reset from a DB9 serial connector.
Figure 4-37: Additional Connection To Reset From DB9
In this configuration, because the software does not directly control power to
the processor, the user will be prompted to turn the processor’s power supply
on and off. Turning off thepower supply is necessary in order to be able to pass
the initial security mode check and access the flash on the processor. A simple
reset is not enough; to pass the security check, you must first force the
processor to encounter a POR (power-on reset) which requires the processor’s
voltage to dip below 0.1v. Once security has been passed, resetting the device
相關PDF資料 |
PDF描述 |
|---|---|
| MULTILYNX | MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver |
| MULTISYNCFE750 | Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| MUM8128W-17 | x8 EPROM |
| MUM8128W-20 | x8 EPROM |
| MUM8128W-25 | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MULTILYNX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver |
| MULTIMAX-8G+ | 功能描述:程序設計器 - 基于通用和內存 HI PERF STAND ALONE PRGRAMER FOR 8-SOCK RoHS:否 制造商:Xeltek 產品:Universal Device Programmers 工具用于評估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口類型:Parallel, USB 工作電源電壓:90 VAC to 250 VAC |
| MULTIPHSPOL-RD | 功能描述:電源管理IC開發工具 Si825x Multi-Phase POL Reference Design RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。