參數資料
型號: P89V51RB2BBC,557
廠商: NXP Semiconductors
文件頁數: 30/80頁
文件大?。?/td> 0K
描述: IC 80C51 MCU 1024 RAM 44TQFP
產品培訓模塊: Migrating from 8/16-Bit MCUs to 32-Bit ARMs
標準包裝: 800
系列: 89V
核心處理器: 8051
芯體尺寸: 8-位
速度: 40MHz
連通性: SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 32
程序存儲器容量: 16KB(16K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 4.5 V ~ 5.5 V
振蕩器型: 內部
工作溫度: 0°C ~ 70°C
封裝/外殼: 44-TQFP
包裝: 托盤
配用: 622-1017-ND - BOARD 44-ZIF PLCC SOCKET
其它名稱: 935277723557
P89V51RB2BBC
P89V51RB2BBC-ND
P89V51RB2_RC2_RD2_5
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 05 — 12 November 2009
36 of 80
NXP Semiconductors
P89V51RB2/RC2/RD2
8-bit microcontrollers with 80C51 core
TCLK = 1, Timer 2 is used as the UART transmit baud rate generator. RCLK has the same
effect for the UART receive baud rate. With these two bits, the serial port can have
different receive and transmit baud rates – Timer 1 or Timer 2.
Figure 15 shows Timer 2 in baud rate generator mode:
The baud rate generation mode is like the auto-reload mode, when a rollover in TH2
causes the Timer 2 registers to be reloaded with the 16-bit value in registers RCAP2H and
RCAP2L, which are preset by software.
The baud rates in modes 1 and 3 are determined by Timer 2’s overow rate given below:
Modes 1 and 3 baud rates = Timer 2 Overow Rate / 16
The timer can be congured for either ‘timer’ or ‘counter’ operation. In many applications,
it is congured for ‘timer' operation (C/T2 = 0). Timer operation is different for Timer 2
when it is being used as a baud rate generator.
Usually, as a timer it would increment every machine cycle (i.e., 1
6 the oscillator
frequency). As a baud rate generator, it increments at the oscillator frequency. Thus the
baud rate formula is as follows:
Modes 1 and 3 baud rates =
(3)
n = 32 in X1 mode, 16 in X2 mode
Where: (RCAP2H, RCAP2L) = The content of RCAP2H and RCAP2L taken as a 16-bit
unsigned integer.
The Timer 2 as a baud rate generator mode is valid only if RCLK and/or TCLK = 1 in
T2CON register. Note that a rollover in TH2 does not set TF2, and will not generate an
interrupt. Thus, the Timer 2 interrupt does not have to be disabled when Timer 2 is in the
baud rate generator mode. Also if the EXEN2 (T2 external enable ag) is set, a 1-to-0
transition in T2EX (Timer/counter 2 trigger input) will set EXF2 (T2 external ag) but will
Fig 15. Timer 2 in Baud Rate Generator mode
002aaa526
TX/RX baud rate
timer 2
interrupt
OSC
÷2
T2 pin
C/T2 = 0
C/T2 = 1
TL2
(8-bits)
TH2
(8-bits)
control
TR2
EXF2
RCAP2L RCAP2H
control
EXEN2
transition
detector
T2EX pin
reload
OscillatorFrequency
n
65536
RCAP2H RCAP2L
,
()
()
×
()
------------------------------------------------------------------------------------------------
相關PDF資料
PDF描述
VJ1825A223JBCAT4X CAP CER 0.022UF 200V 5% NP0 1825
VJ1825A223KBCAT4X CAP CER 0.022UF 200V NP0 1825
VJ2225A562JBAAT4X CAP CER 5600PF 50V 5% NP0 2225
VJ2225A562JBBAT4X CAP CER 5600PF 100V 5% NP0 2225
VJ2225A562JBCAT4X CAP CER 5600PF 200V 5% NP0 2225
相關代理商/技術參數
參數描述
P89V51RB2FA 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 16K FLASH PLCC44
P89V51RB2FA,529 功能描述:8位微控制器 -MCU 80C51 16K FL / 512 R RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89V51RB2FA529 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 40MHZ LCC-44
P89V51RB2FN 制造商:NXP Semiconductors 功能描述:IC MCU 8BIT 80C51 16K FLASH DIP40 制造商:NXP Semiconductors 功能描述:IC, MCU 8BIT 80C51 16K FLASH, DIP40
P89V51RB2FN,112 功能描述:8位微控制器 -MCU 80C51 16K FL / 512 R RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT