參數資料
型號： PEB3065
廠商： SIEMENS AG
元件分類： Codec
英文描述： Signal Processing Subscriber Line Interface Codec Filter SLICOF
中文描述： 信號處理用戶線路接口編解碼器SLICOF
文件頁數： 47/102頁
文件大?。?/td> 563K
代理商： PEB3065
PEB 3065
PEF 3065
Operating Modes
Semiconductor Group
47
01.98
6.1
The SLICOFI has 3 different reset sources that are all internally connected.
The Reset pin RES
(pin 36), which works totally asynchronous to the external clocks.
The Reset bit
(Within SOP - command, bit 4). The reset is valid for SOP-write only.
Power On Reset.
If internal
V
DDD
gets above 1.5 Volts the SLICOFI is Reset by Power
On Reset.
All 3 different sources set the SLICOFI to the basic setting modes (see below).
After a reset caused by any of the sources mentioned above, the reset bit
(SCR0-4 = RSTST) in read direction is set to one. This bit is cleared (RSTST = 0) after
it has been read by a SOP-read operation with the LSEL bits set to 00b (means: read
only SCR0 byte). A SOP-read with other LSEL bits reads the actual RSTST value, but
does not clear it.
The Reset pin RES has a Schmitt-Trigger input to reduce the sensitivity for spikes. In
addition the pin RES has a spike rejection. All spikes smaller than typ. 70 ns are
neglected. The pin RES can be set to 1 for an unlimited time but at least 125
μ
s is
recommended; during that, the DU pin is set to high impedance.
The SLICOFI leaves this mode automatically with the beginning of the next 8 kHz-frame
(or after pin RES is released).
Reset Behavior
6.2
After RESET, the SLICOFI automatically is switched to its basic settings in which it uses
internal default values for all filters and settings (AC and DC), so that the SLMA still
works in a kind of “emergency mode” and can be handled by C/I-Interface commands
only.
This means that for an (un-)determined reset (e.g. Power On Reset) the SLICOFI is
reset, but can be switched to or return automatically to any operating mode presented to
the C/I-channel after 2 FSC cycles. In all modes the SLMA stays stable, supervision and
DC-feeding are still working and conversation can go on in a proper way until all filters
and settings have been reloaded by SOP and COP-commands.
So what happens internally after reset
– all configuration registers are set to their default values (note that the Coefficient RAM
is
not
reset)
– the RSTST-bit (SCR0-4) is set to 1 to indicate that a reset has taken place
– The IOM-2 interface is reset. Running communication is stopped
– DU is in high impedance state
– AC- and DC-loop use the default values and not the programmed ones (see below)
Basic Setting Modes
相關PDF資料
PDF描述
PEB3065NV3.2 Signal Processing Subscriber Line Interface Codec Filter SLICOF
PEF3065NV3.2 Signal Processing Subscriber Line Interface Codec Filter SLICOF
PEB3086 ISDN SUBSCRIBER ACCESS CONTROLLER
PEB31665 NMultichannel Subscriber Line Interface Concept MuSLIC
PEB3465 NMultichannel Subscriber Line Interface Concept MuSLIC
相關代理商/技術參數
參數描述
PEB3065NV3.2 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Signal Processing Subscriber Line Interface Codec Filter SLICOF
PEB3065-NV3.2 制造商:Infineon Technologies AG 功能描述:A/MU-LAW, PCM CODEC, 44 Pin Plastic PLCC 制造商:Siemens 功能描述:A/MU-LAW, PCM CODEC, 44 Pin Plastic PLCC
PEB3065NV3.2SLICOFI 制造商:Rochester Electronics LLC 功能描述:- Bulk
PEB3065NV3.2-SLICOFI 制造商:Rochester Electronics LLC 功能描述:- Bulk
PEB3081 制造商:未知廠家 制造商全稱:未知廠家 功能描述:3.3 V S-Bus Interface Circuit eXtended
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*