參數資料
型號： PIC16C712-04/SO
廠商： Microchip Technology
文件頁數： 70/106頁
文件大小： 0K
描述： IC MCU OTP 1KX14 A/D PWM 18SOIC
產品培訓模塊： Asynchronous Stimulus
標準包裝： 42
系列： PIC® 16C
核心處理器： PIC
芯體尺寸： 8-位
速度： 4MHz
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 13
程序存儲器容量： 1.75KB（1K x 14）
程序存儲器類型： OTP
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 4 V ~ 5.5 V
數據轉換器： A/D 4x8b
振蕩器型： 外部
工作溫度： 0°C ~ 70°C
封裝/外殼： 18-SOIC（0.295"，7.50mm 寬）
包裝： 管件
PIC16C712/716
DS41106B-page 64
2005 Microchip Technology Inc.
9.13
Power-down Mode (Sleep)
Power-Down mode is entered by executing a SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the PD bit (STATUS<3>) is cleared, the
TO (STATUS<4>) bit is set, and the oscillator driver is
turned off. The I/O ports maintain the status they had,
before the SLEEP instruction was executed (driving
high, low, or high-impedance).
For lowest current consumption in this mode, place all
I/O pins at either VDD or VSS, ensure no external
circuitry is drawing current from the I/O pin, power-
down the A/D and the disable external clocks. Pull all I/
O pins, that are high-impedance inputs, high or low
externally to avoid switching currents caused by float-
ing inputs. The T0CKI input should also be at VDD or
VSS for lowest current consumption. The contribution
from on-chip pull-ups on PORTB should be considered.
The MCLR pin must be at a logic high level (VIHMC).
9.13.1
WAKE-UP FROM SLEEP
The device can wake up from Sleep through one of the
following events:
1.
External Reset input on MCLR pin.
2.
Watchdog
Timer
Wake-up
(if
WDT
was
enabled).
3.
Interrupt from INT pin, RB port change, or some
peripheral interrupts.
External MCLR Reset will cause a device Reset. All
other events are considered a continuation of program
execution and cause a “wake-up”. The TO and PD bits
in the STATUS register can be used to determine the
cause of device Reset. The PD bit, which is set on
power-up, is cleared when SLEEP is invoked. The TO
bit is cleared if a WDT Time-out occurred (and caused
wake-up).
The following peripheral interrupts can wake the device
from Sleep:
1.
TMR1 interrupt. Timer1 must be operating as an
asynchronous counter.
2.
CCP Capture mode interrupt.
3.
Special Event Trigger (Timer1 in Asynchronous
mode using an external clock).
Other peripherals cannot generate interrupts, since
during Sleep, no on-chip clocks are present.
相關PDF資料
PDF描述
W2L16C474MAT1A CAP CER 0.47UF 6.3V 20% X7R 0508
W2L16C334MAT1S CAP CER 0.33UF 6.3V 20% X7R 0508
V110A28C400BL2 CONVERTER MOD DC/DC 28V 400W
W2L16C334MAT1A CAP CER 0.33UF 6.3V 20% X7R 0508
W2L14D684MAT1S CAP CER 0.68UF 4V 20% X7R 0508
相關代理商/技術參數
參數描述
PIC16C71-20I/P 功能描述:8位微控制器 -MCU 1.75KB 36 RAM 13 I/O 20MHz IndTemp PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C71-20I/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C71 DIP18
PIC16C71-20I/SO 功能描述:8位微控制器 -MCU 1.75KB 36 RAM 13 I/O 20MHz IndTemp SOIC18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C712-20/P 功能描述:8位微控制器 -MCU 1.75KB OTP 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C712-20/SO 功能描述:8位微控制器 -MCU 1.75KB 128RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*