參數資料
型號: PIC16F872T-E/SS
廠商: Microchip Technology
文件頁數: 9/167頁
文件大?。?/td> 0K
描述: IC MCU CMOS 20MHZ 2K FLSH 28SSOP
標準包裝: 2,100
系列: PIC® 16F
核心處理器: PIC
芯體尺寸: 8-位
速度: 20MHz
連通性: I²C,SPI
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 22
程序存儲器容量: 3.5KB(2K x 14)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 64 x 8
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 4 V ~ 5.5 V
數據轉換器: A/D 5x10b
振蕩器型: 外部
工作溫度: -40°C ~ 125°C
封裝/外殼: 28-SSOP(0.209",5.30mm 寬)
包裝: 帶卷 (TR)
106
8048C–AVR–02/12
ATtiny43U
14.3.3
SPI Slave Operation Example
The following code demonstrates how to use the USI module as a SPI Slave:
init:
ldi
r16,(1<<USIWM0)|(1<<USICS1)
out
USICR,r16
...
SlaveSPITransfer:
out
USIDR,r16
ldi
r16,(1<<USIOIF)
out
USISR,r16
SlaveSPITransfer_loop:
in
r16, USISR
sbrs
r16, USIOIF
rjmp
SlaveSPITransfer_loop
in
r16,USIDR
ret
The code is size optimized using only eight instructions (plus return). The code example
assumes that the DO and USCK pins have been enabled as outputs in DDRA. The value stored
in register r16 prior to the function is called is transferred to the master device, and when the
transfer is completed the data received from the master is stored back into the register r16.
Note that the first two instructions are for initialization, only, and need only be executed once.
These instructions set three-wire mode and positive edge clock. The loop is repeated until the
USI Counter Overflow Flag is set.
14.3.4
Two-wire Mode
The USI two-wire mode is compliant to the Inter IC (TWI) bus protocol, but without slew rate lim-
iting on outputs and without input noise filtering. Pin names used in this mode are SCL and SDA.
Figure 14-4 shows two USI units operating in two-wire mode, one as master and one as slave. It
is only the physical layer that is shown since the system operation is highly dependent of the
communication scheme used. The main differences between the master and slave operation at
this level is the serial clock generation which is always done by the master. Only the slave uses
the clock control unit.
Clock generation must be implemented in software, but the shift operation is done automatically
in both devices. Note that clocking only on negative edges for shifting data is of practical use in
this mode. The slave can insert wait states at start or end of transfer by forcing the SCL clock
low. This means that the master must always check if the SCL line was actually released after it
has generated a positive edge.
Since the clock also increments the counter, a counter overflow can be used to indicate that the
transfer is completed. The clock is generated by the master by toggling the USCK pin via the
PORTA register.
相關PDF資料
PDF描述
3-1734248-6 CONN FPC/ZIF 36POS 1MM VERT SMD
PIC16F872T-E/SO IC MCU CMOS 20MHZ 2K FLSH 28SOIC
PIC16F727-E/P IC PIC MCU FLASH 8KX14 40-DIP
PIC16F871T-E/PT IC MCU CMOS 20MHZ 2K FLSH 44TQFP
PIC16F871T-E/L IC MCU CMOS 20MHZ 2K FLSH 44PLCC
相關代理商/技術參數
參數描述
PIC16F872T-I/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F872T-I/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F872T-I/SS033 制造商:Microchip Technology Inc 功能描述:
PIC16F873-04/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F873-04/SO 制造商:Microchip Technology Inc 功能描述:8BIT FLASH MCU SMD 16F873 SOIC28