參數資料
型號: PIC18F6720-I/PT
廠商: Microchip Technology
文件頁數: 41/165頁
文件大?。?/td> 0K
描述: IC MCU FLASH 64KX16 EE 64TQFP
產品培訓模塊: Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝: 160
系列: PIC® 18F
核心處理器: PIC
芯體尺寸: 8-位
速度: 25MHz
連通性: I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,LVD,POR,PWM,WDT
輸入/輸出數: 52
程序存儲器容量: 128KB(64K x 16)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 1K x 8
RAM 容量: 3.75K x 8
電壓 - 電源 (Vcc/Vdd): 4.2 V ~ 5.5 V
數據轉換器: A/D 12x10b
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 64-TQFP
包裝: 托盤
配用: MA180020-ND - MODULE PLUG-IN HPC EXPL 18F87J11
XLT64PT5-ND - SOCKET TRAN ICE 64MQFP/TQFP
AC164319-ND - MODULE SKT MPLAB PM3 64TQFP
2004 Microchip Technology Inc.
DS39609B-page 133
PIC18F6520/8520/6620/8620/6720/8720
11.1
Timer0 Operation
Timer0 can operate as a timer or as a counter.
Timer mode is selected by clearing the T0CS bit. In
Timer mode, the Timer0 module will increment every
instruction cycle (without prescaler). If the TMR0 regis-
ter is written, the increment is inhibited for the following
two instruction cycles. The user can work around this
by writing an adjusted value to the TMR0 register.
Counter mode is selected by setting the T0CS bit. In
Counter mode, Timer0 will increment, either on every
rising or falling edge of pin RA4/T0CKI. The increment-
ing edge is determined by the Timer0 Source Edge
Select bit (T0SE). Clearing the T0SE bit selects the
rising edge. Restrictions on the external clock input are
discussed below.
When an external clock input is used for Timer0, it must
meet certain requirements. The requirements ensure
the external clock can be synchronized with the internal
phase clock (TOSC). Also, there is a delay in the actual
incrementing of Timer0 after synchronization.
11.2
Prescaler
An 8-bit counter is available as a prescaler for the Timer0
module. The prescaler is not readable or writable.
The PSA and T0PS2:T0PS0 bits determine the
prescaler assignment and prescale ratio.
Clearing bit PSA will assign the prescaler to the Timer0
module. When the prescaler is assigned to the Timer0
module, prescale values of 1:2, 1:4, ..., 1:256 are
selectable.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF TMR0, MOVWF
TMR0
, BSF TMR0, x, ..., etc.) will clear the prescaler
count.
11.2.1
SWITCHING PRESCALER
ASSIGNMENT
The prescaler assignment is fully under software
control, (i.e., it can be changed “on-the-fly” during
program execution).
11.3
Timer0 Interrupt
The TMR0 interrupt is generated when the TMR0
register overflows from FFh to 00h in 8-bit mode, or
FFFFh to 0000h in 16-bit mode. This overflow sets the
TMR0IF bit. The interrupt can be masked by clearing
the TMR0IE bit. The TMR0IF bit must be cleared in
software by the Timer0 module Interrupt Service
Routine before re-enabling this interrupt. The TMR0
interrupt cannot awaken the processor from Sleep,
since the timer is shut-off during Sleep.
11.4
16-Bit Mode Timer Reads
and Writes
TMR0H is not the high byte of the timer/counter in
16-bit mode, but is actually a buffered version of the
high byte of Timer0 (refer to Figure 11-2). The high byte
of the Timer0 counter/timer is not directly readable nor
writable. TMR0H is updated with the contents of the
high byte of Timer0 during a read of TMR0L. This pro-
vides the ability to read all 16 bits of Timer0 without
having to verify that the read of the high and low byte
were valid, due to a rollover between successive reads
of the high and low byte.
A write to the high byte of Timer0 must also take place
through the TMR0H Buffer register. Timer0 high byte is
updated with the contents of TMR0H when a write
occurs to TMR0L. This allows all 16 bits of Timer0 to be
updated at once.
TABLE 11-1:
REGISTERS ASSOCIATED WITH TIMER0
Note:
Writing to TMR0 when the prescaler is
assigned
to
Timer0,
will
clear
the
prescaler count, but will not change the
prescaler assignment.
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
POR, BOR
Value on
all other
Resets
TMR0L
Timer0 Module Low Byte Register
xxxx xxxx uuuu uuuu
TMR0H
Timer0 Module High Byte Register
0000 0000 0000 0000
INTCON
GIE/GIEH PEIE/GIEL TMR0IE INT0IE
RBIE
TMR0IF INT0IF
RBIF
0000 0000 0000 0000
T0CON
TMR0ON
T08BIT
T0CS
T0SE
PSA
T0PS2
T0PS1
T0PS0 1111 1111 1111 1111
TRISA
PORTA Data Direction Register
-111 1111 -111 1111
Legend: x = unknown, u = unchanged, – = unimplemented locations, read as ‘0’.
Shaded cells are not used by Timer0.
相關PDF資料
PDF描述
PIC18LF6723-I/PT IC PIC MCU FLASH 64KX16 64TQFP
PIC17C756A-33I/L IC MCU OTP 16KX16 A/D PWM 68PLCC
PIC18F6723-I/PT IC PIC MCU FLASH 64KX16 64TQFP
PIC18LF6620-I/PT IC MCU FLSH 1MBIT W/AD LP 64TQFP
65175-002LF BP COVER LF
相關代理商/技術參數
參數描述
PIC18F6720T-E/PT 功能描述:8位微控制器 -MCU 25MHz 128KB Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F6720T-I/PT 功能描述:8位微控制器 -MCU 128KB 3840 RAM 52I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F6720T-I/PTC01 制造商:Microchip Technology Inc 功能描述:PIC18 Series 3.75 kB RAM 128 kB Flash 8-Bit Microcontroller - TQFP-64
PIC18F6720TIPT 制造商:MICROCHIP 功能描述:TOFP SHIPS IN 24 HOURS GREEN
PIC18F6721-I/PT 功能描述:8位微控制器 -MCU 128kBF 4096RM 40MHz nonoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT