- 您現在的位置：買賣IC網 > PDF目錄376309 > RH56D-PCI (Conexant Systems, Inc.) Host Controlled V.90/K56flex Modem device PDF資料下載
參數資料
| 型號： | RH56D-PCI |
| 廠商： | Conexant Systems, Inc. |
| 英文描述： | Host Controlled V.90/K56flex Modem device |
| 中文描述： | 主機控制V.90/K56flex調制解調器設備 |
| 文件頁數： | 35/60頁 |
| 文件大?。?/td> | 357K |
| 代理商： | RH56D-PCI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
RH56D-PCI Modem Designer’s Guide
1213
Conexant
4-1
Conexant Proprietary Information
4. DESIGN CONSIDERATIONS
Good engineering practices must be followed when designing a printed circuit board (PCB) containing the modem device.
This is especially important considering the high data bit rate, high fax rate, record/play of analog speech and music audio,
and full-duplex speakerphone operation. Suppression of noise is essential to the proper operation and performance of the
modem and interfacing audio and DAA circuits.
Two aspects of noise in an OEM board design containing the modem device set must be considered: on-board/off-board
generated noise that can affect analog signal levels and analog-to-digital conversion (ADC)/digital-to-analog conversion
(DAC), and on-board generated noise that can radiate off-board. Both on-board and off-board generated noise that is coupled
on-board can affect interfacing signal levels and quality, especially in low level analog signals. Of particular concern is noise
in frequency ranges affecting modem and audio circuit performance.
On-board generated electromagnetic interference (EMI) noise that can be radiated or conducted off-board is a separate, but
equally important, concern. This noise can affect the operation of surrounding equipment. Most local governing agencies
have stringent certification requirements that must be met for use in specific environments. In order to minimize the
contribution of the circuit design and PCB layout to EMI, the designer must understand the major sources of EMI and how to
reduce them to acceptable levels.
Proper PC board layout (component placement and orientation, signal routing, trace thickness and geometry, etc.),
component selection (composition, value, and tolerance), interface connections, and shielding are required for the board
design to achieve desired modem performance and to attain EMI certification. In addition, design layout should meet
requirements stated in the PCI Bus Specification, Section 4.4, Expansion Board Specification, as well as other applicable
sections.
All the aspects of proper engineering practices are beyond the scope of this designer's guide. The designer should consult
noise suppression techniques described in technical publications and journals, electronics and electrical engineering text
books, and component supplier application notes. Seminars addressing noise suppression techniques are often offered by
technical and professional associations as well as component suppliers.
The following guidelines are offered to specifically help achieve stated modem performance, minimize audible noise for audio
circuit use, and to minimize EMI generation.
4.1 PC BOARD LAYOUT GUIDELINES
4.1.1 General Principles
1. Provide separate digital, analog, and DAA sections on the board.
2. Keep digital and analog components and their corresponding traces as separate as possible and confined to defined
sections.
3. Keep high speed digital traces as short as possible.
4. Keep sensitive analog traces as short as possible.
5. Provide proper power supply distribution, grounding, and decoupling.
6. Provide separate digital ground, analog ground, and chassis ground (if appropriate) planes.
7. Provide wide traces for power and critical signals.
8. Position digital circuits near the host bus connection and position the DAA circuits near the telephone line connections.
4.1.2 Component Placement
1. From the system circuit schematic,
a) Identify the digital, analog, and DAA circuits and their components, as well as external signal and power
connections.
b) Identify the digital, analog, mixed digital/analog components within their respective circuits.
c) Note the location of power and signals pins for each device (IC).
2. Roughly position digital, analog, and DAA circuits on separate sections of the board. Keep the digital and analog
components and their corresponding traces as separate as possible and confined to their respective sections on the
board. Typically, the digital circuits will cover one-half of the board, analog circuits will cover one-fourth of the board, and
the DAA will cover one-fourth of the board.
NOTE:
While the DAA is primarily analog in nature, it also has many control
相關PDF資料 |
PDF描述 |
|---|---|
| RHF-24(2) | LOW-POWER DISSIPATION ADSL LINE DRIVER |
| RI-60 | Ultra-miniature dry-reed switch hermetically sealed in a gas-filled glass envelope |
| RI60 | Ultra-miniature dry-reed switch germetically sealed in a gas-dilled glass envelope |
| RI-ANT-S01C-00 | SERIES 2000 ANTENNAS |
| RI-I01-110A | Tag-it HF Transponder Inlay Square |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RH56M-4/122156 | 制造商:ebm-papst Inc 功能描述: |
| RH56M-4/210928 | 制造商:ebm-papst Inc 功能描述: |
| RH56M-6/127804 | 制造商:ebm-papst Inc 功能描述: |
| RH56M-6/204689 | 制造商:ebm-papst Inc 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。