參數資料
型號: RH80532NC017256
元件分類: 微處理器
英文描述: Microprocessor
中文描述: 微處理器
文件頁數: 53/93頁
文件大?。?/td> 2353K
代理商: RH80532NC017256
Mobile Intel
Pentium
4 Processor-M
250686-002
Datasheet
53
3.3
System Bus Signal Quality Specifications and
Measurement Guidelines
3.3.1
Overshoot/Undershoot Guidelines
Overshoot (or undershoot) is the absolute value of the maximum voltage above the nominal high
voltage (or below V
) as shown in
Figure 30
. The overshoot guideline limits transitions beyond
V
CC
or V
SS
due to the fast signal edge rates. The processor can be damaged by repeated overshoot
or undershoot events on any input, output, or I/O buffer if the charge is large enough (i.e., if the
over/undershoot is great enough). Determining the impact of an overshoot/undershoot condition
requires knowledge of the magnitude, the pulse direction, and the activity factor (AF). Permanent
damage to the processor is the likely result of excessive overshoot/undershoot.
When performing simulations to determine impact of overshoot and undershoot, ESD diodes must
be properly characterized. ESD protection diodes do not act as voltage clamps and will not provide
overshoot or undershoot protection. ESD diodes modelled within Intel I/O buffer models do not
clamp undershoot or overshoot and will yield correct simulation results. If other I/O buffer models
are being used to characterize the Mobile Intel Pentium 4 Processor-M system bus, care must be
taken to ensure that ESD models do not clamp extreme voltage levels. Intel I/O buffer models also
contain I/O capacitance characterization. Therefore, removing the ESD diodes from an I/O buffer
model will impact results and may yield excessive overshoot/undershoot.
3.3.2
Overshoot/Undershoot Magnitude
Magnitude describes the maximum potential difference between a signal and its voltage reference
level. For the Mobile Intel Pentium 4 Processor-M both are referenced to V
SS
. It is important to
note that overshoot and undershoot conditions are separate and their impact must be determined
independently.
Overshoot/undershoot magnitude levels must observe the absolute maximum specifications listed
in
Table 29
through
Table 32
. These specifications must not be violated at any time regardless of
bus activity or system state. Within these specifications are threshold levels that define different
allowed pulse durations. Provided that the magnitude of the overshoot/undershoot is within the
absolute maximum specifications, the pulse magnitude, duration and activity factor must all be
used to determine if the overshoot/undershoot pulse is within specifications.
3.3.3
Overshoot/Undershoot Pulse Duration
Pulse duration describes the total time an overshoot/undershoot event exceeds the overshoot/
undershoot reference voltage (maximum overshoot = 1.700 V, maximum undershoot = -0.400 V).
The total time could encompass several oscillations above the reference voltage. Multiple
overshoot/undershoot pulses within a single overshoot/undershoot event may need to be measured
to determine the total pulse duration.
相關PDF資料
PDF描述
RH80532NC021256 Microprocessor
RH80532NC025256 Microprocessor
RH80532NC029256 Microprocessor
RH80532NC033256 Microprocessor
RHE070 Poly Switch PTC DEVICES
相關代理商/技術參數
參數描述
RH80532NC021256 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
RH80532NC025256 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
RH80532NC029256 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
RH80532NC033256 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
RH80532NC049256 制造商:Rochester Electronics LLC 功能描述:- Bulk