- 您現在的位置：買賣IC網 > PDF目錄372109 > SAA3323H (NXP SEMICONDUCTORS) Drive processor for DCC systems PDF資料下載
參數資料
| 型號： | SAA3323H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | Drive processor for DCC systems |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| 封裝： | 12 X 12 MM, 1.40 MM HEIGHT, PLASTIC, SOT-315-1, TQFP-80 |
| 文件頁數： | 54/56頁 |
| 文件大?。?/td> | 274K |
| 代理商： | SAA3323H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁
May 1994
54
Philips Semiconductors
Preliminary specification
Drive processor for DCC systems
SAA3323
SOLDERING
Plastic quad flatpacks
B
Y WAVE
During placement and before soldering, the component
must be fixed with a droplet of adhesive. After curing the
adhesive, the component can be soldered. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder bath is
10 s, if allowed to cool to less than 150
°
C within 6 s.
Typical dwell time is 4 s at 250
°
C.
A modified wave soldering technique is recommended
using two solder waves (dual-wave), in which a turbulent
wave with high upward pressure is followed by a smooth
laminar wave. Using a mildly-activated flux eliminates the
need for removal of corrosive residues in most
applications.
B
Y SOLDER PASTE REFLOW
Reflow soldering requires the solder paste (a suspension
of fine solder particles, flux and binding agent) to be
applied to the substrate by screen printing, stencilling or
pressure-syringe dispensing before device placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt, infrared, and
vapour-phase reflow. Dwell times vary between 50 and
300 s according to method. Typical reflow temperatures
range from 215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 min at 45
°
C.
R
EPAIRING SOLDERED JOINTS
(
BY HAND
-
HELD SOLDERING
IRON OR PULSE
-
HEATED SOLDER TOOL
)
Fix the component by first soldering two, diagonally
opposite, end pins. Apply the heating tool to the flat part of
the pin only. Contact time must be limited to 10 s at up to
300
°
C. When using proper tools, all other pins can be
soldered in one operation within 2 to 5 s at between 270
and 320
°
C. (Pulse-heated soldering is not recommended
for SO packages.)
For pulse-heated solder tool (resistance) soldering of VSO
packages, solder is applied to the substrate by dipping or
by an extra thick tin/lead plating before package
placement.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA3500H | Digital audio broadcast channel decoder |
| SAA4700T | VPS dataline processor |
| SAA4700 | VPS dataline processor |
| SAA4945H | LIne MEmory noise Reduction IC LIMERIC |
| SAA4951 | RES 6.49K OHM 1/16W 0.5% 0402SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA33299003 | 制造商:LG Corporation 功能描述:S/W,Firmware |
| SAA33308202 | 制造商:LG Corporation 功能描述:S/W,Firmware |
| SAA33333703 | 制造商:LG Corporation 功能描述:S/W,Firmware |
| SAA33378323 | 制造商:LG Corporation 功能描述:S/W,Firmware |
| SAA33378405 | 制造商:LG Corporation 功能描述:S/W,Firmware |
發布緊急采購，3分鐘左右您將得到回復。