參數資料
型號： SC16C652BIBS
廠商： NXP Semiconductors N.V.
元件分類： 收發器
英文描述： 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.) with 32-byte FIFOs and infrared (IrDA) encoder-decoder
封裝： SC16C652BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html<1<Always Pb-free,;SC16C652BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html&
文件頁數： 9/43頁
文件大小： 210K
代理商： SC16C652BIBS
SC16C652B_4
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 04 — 1 September 2005
9 of 43
Philips Semiconductors
SC16C652B
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
6.3 FIFO operation
The 32-byte transmit and receive data FIFOs are enabled by the FIFO Control Register
bit 0 (FCR[0]). With 16C2550 devices, the user can set the receive trigger level, but not
the transmit trigger level. The SC16C652B provides independent trigger levels for both
receiver and transmitter. To remain compatible with SC16C2550, the transmit interrupt
trigger level is set to 16 following a reset. It should be noted that the user can set the
transmit trigger levels by writing to the FCR, but activation will not take place until EFR[4]
is set to a logic 1. The receiver FIFO section includes a time-out function to ensure data is
delivered to the external CPU. An interrupt is generated whenever the Receive Holding
Register (RHR) has not been read following the loading of a character or the receive
trigger level has not been reached.
6.4 Hardware flow control
When automatic hardware flow control is enabled, the SC16C652B monitors the CTS pin
for a remote buffer overflow indication and controls the RTS pin for local buffer overflows.
Automatic hardware flow control is selected by setting EFR[6] (RTS) and EFR[7] (CTS) to
a logic 1. If CTS transitions from a logic 0 to a logic 1 indicating a flow control request,
ISR[5] will be set to a logic 1 (if enabled via IER[7:6]), and the SC16C652B will suspend
TX transmissions as soon as the stop bit of the character in process is shifted out.
Transmission is resumed after the CTS input returns to a logic 0, indicating more data may
be sent.
With the Auto-RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed trigger level. The RTS pin will not be forced to a logic 1 (RTS
off), until the receive FIFO reaches the next trigger level. However, the RTS pin will return
to a logic 0 after the data buffer (FIFO) is unloaded to the next trigger level below the
programmed trigger level. However, under the above described conditions, the
SC16C652B will continue to accept data until the receive FIFO is full.
6.5 Software flow control
When software flow control is enabled, the SC16C652B compares one or two sequential
receive data characters with the programmed Xon or Xoff character value(s). If received
character(s) match the programmed Xoff values, the SC16C652B will halt transmission
(TX) as soon as the current character(s) has completed transmission. When a match
occurs, the receive ready (if enabled via Xoff IER[5]) flags will be set and the interrupt
output pin (if receive interrupt is enabled) will be activated. Following a suspension due to
a match of the Xoff characters’ values, the SC16C652B will monitor the receive data
stream for a match to the Xon1/Xon2 character value(s). If a match is found, the
SC16C652B will resume operation and clear the flags (ISR[4]).
Table 5:
Selected trigger level
(characters)
Flow control mechanism
INT pin activation
RX
8
16
24
28
Negate RTS or
send Xoff
Assert RTS or
send Xon
TX
16
8
24
30
8
16
24
28
8
16
24
28
0
7
15
23
相關PDF資料
PDF描述
SC16C654BIA68 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654B 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
SC16C654BIB64 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654BIBM 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654BIBS 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
相關代理商/技術參數
參數描述
SC16C652BIBS,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIBS,151 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIBS,157 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIBS-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIBS-S 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*