- 您現在的位置：買賣IC網 > PDF目錄1967 > SC16C850IBS/Q900,5 (NXP Semiconductors)IC UART SGL UNIV ASYNC 36-VFQFN PDF資料下載
參數資料
| 型號： | SC16C850IBS/Q900,5 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 17/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SGL UNIV ASYNC 36-VFQFN |
| 標準包裝： | 1 |
| 特點： | 可編程 |
| 通道數： | 1，UART |
| FIFO's： | 128 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.5 V ~ 3.3 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-HVQFN（5x5） |
| 包裝： | 標準包裝 |
| 其它名稱： | 568-6566-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
24 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
7.2.1 IER versus Transmit/Receive FIFO interrupt mode operation
When the receive FIFO is enabled (FCR[0] = logic 1), and receive interrupts
(IER[0] = logic 1) are enabled, the receive interrupts and register status will reflect the
following:
The receive RXRDY interrupt (Level 2 ISR interrupt) is issued to the external CPU
when the receive FIFO has reached the programmed trigger level. It will be cleared
when the receive FIFO drops below the programmed trigger level.
Receive FIFO status will also be reflected in the user accessible ISR register when
the receive FIFO trigger level is reached. Both the ISR register receive status bit and
the interrupt will be cleared when the FIFO drops below the trigger level.
The receive data ready bit (LSR[0]) is set as soon as a character is transferred from
the shift register (RSR) to the receive FIFO. It is reset when the FIFO is empty.
When the Transmit FIFO and interrupts are enabled, an interrupt is generated when
the transmit FIFO is empty due to the unloading of the data by the TSR and UART for
transmission via the transmission media. The interrupt is cleared either by reading the
ISR, or by loading the THR with new data characters.
7.2.2 IER versus Receive/Transmit FIFO polled mode operation
When FCR[0] = logic 1, setting IER[3:0] puts the SC16C850 in the FIFO polled mode of
operation. In this mode, interrupts are not generated and the user must poll the LSR
register for TX and/or RX data status. Since the receiver and transmitter have separate
bits in the LSR either or both can be used in the polled mode by selecting respective
transmit or receive control bit(s).
LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.
LSR[4:1] will provide the type of receive errors, or a receive break, if encountered.
LSR[5] will indicate when the transmit FIFO is empty.
LSR[6] will indicate when both the transmit FIFO and transmit shift register are empty.
LSR[7] will show if any FIFO data errors occurred.
1
IER[1]
Transmit Holding Register interrupt. In the non-FIFO mode, this interrupt will be
issued whenever the THR is empty, and is associated with LSR[5]. In the FIFO
modes, this interrupt will be issued whenever the FIFO is empty.
logic 0 = disable the Transmit Holding Register Empty (TXRDY) interrupt
(normal default condition)
logic 1 = enable the TXRDY (ISR level 3) interrupt
0
IER[0]
Receive Holding Register interrupt. In the non-FIFO mode, this interrupt will be
issued when the RHR has data, or is cleared when the RHR is empty. In the FIFO
mode, this interrupt will be issued when the FIFO has reached the programmed
trigger level or is cleared when the FIFO drops below the trigger level.
logic 0 = disable the receiver ready (ISR level 2, RXRDY) interrupt (normal
default condition)
logic 1 = enable the RXRDY (ISR level 2) interrupt
Table 9.
Interrupt Enable Register bits description …continued
Bit
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C852VIET,151 | IC UART DUAL W/FIFO 36TFBGA |
| SC16IS741IPW,112 | IC UART 16TSSOP |
| SC16IS750IBS,151 | IC UART I2C/SPI 24-HVQFN |
| SC16IS762IBS,151 | IC UART DUAL I2C/SPI 32-HVQFN |
| SC26C92A1N,112 | IC UART 40-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C850IET | 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850IET,115 | 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850IET,151 | 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850IET,157 | 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850IET-G | 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。