參數資料
型號： SC16C850VIBS
廠商： NXP Semiconductors N.V.
元件分類： 收發器
英文描述： 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
封裝： SC16C850VIBS<SOT617-1 (HVQFN32)|<<http://www.nxp.com/packages/SOT617-1.html<1<Always Pb-free,;SC16C850VIBS<SOT617-1 (HVQFN32)|<<http://www.nxp.com/packages/SOT617-1.html&
文件頁數： 10/48頁
文件大?。?/td> 338K
代理商： SC16C850VIBS
SC16C850V
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 19 January 2011
10 of 48
NXP Semiconductors
SC16C850V
Single UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
In the event that the receive buffer is overfilling, the SC16C850V automatically sends an
Xoff character (when enabled) via the serial TX output to the remote UART. The
SC16C850V sends the Xoff1/Xoff2 characters as soon as the number of received data in
the receive FIFO passes the programmed trigger level. To clear this condition, the
SC16C850V will transmit the programmed Xon1/Xon2 characters as soon as the number
of characters in the receive FIFO drops below the programmed trigger level.
6.7 Special character detect
A special character detect feature is provided to detect an 8-bit character when EFR[5] is
set. When an 8-bit character is detected, it will be placed on the user-accessible data
stack along with normal incoming RX data. This condition is selected in conjunction with
EFR[3:0] (see
Table 24
). Note that software flow control should be turned off when using
this special mode by setting EFR[3:0] to all zeroes.
The SC16C850V compares each incoming receive character with Xoff2 data. If a match
occurs, the received data will be transferred to the FIFO, and ISR[4] will be set to indicate
detection of a special character. Although
Table 7 “SC16C850V internal registers”
shows
Xon1, Xon2, Xoff1, Xoff2 with eight bits of character information, the actual number of bits
is dependent on the programmed word length. Line Control Register bits LCR[1:0] define
the number of character bits, that is, either 5 bits, 6 bits, 7 bits or 8 bits. The word length
selected by LCR[1:0] also determine the number of bits that will be used for the special
character comparison. Bit 0 in the Xon1, Xon2, Xoff1, Xoff2 registers corresponds with the
LSB bit for the received character.
6.8 Interrupt priority and time-out interrupts
The interrupts are enabled by IER[7:0]. Care must be taken when handling these
interrupts. Following a reset, if Interrupt Enable Register (IER) bit 1 = 1, the SC16C850V
will issue a Transmit Holding Register interrupt. This interrupt must be serviced prior to
continuing operations. The ISR indicates the current singular highest priority interrupt
only. A condition can exist where a higher priority interrupt masks the lower priority
interrupt(s) (see
Table 12
). Only after servicing the higher pending interrupt will the lower
priority interrupt(s) be reflected in the status register. Servicing the interrupt without
investigating further interrupt conditions can result in data errors.
Receive Data Ready and Receive Time Out have the same interrupt priority (when
enabled by IER[0]), and it is important to serve these interrupts correctly. The receiver
issues an interrupt after the number of characters have reached the programmed trigger
level. In this case, the SC16C850V FIFO may hold more characters than the programmed
trigger level. Following the removal of a data byte, the user should re-check LSR[0] to see
if there are any additional characters. A Receive Time Out will not occur if the receive
FIFO is empty. The time-out counter is reset at the center of each stop bit received or
each time the Receive Holding Register (RHR) is read. The actual time-out value is
4 character time, including data information length, start bit, parity bit, and the size of stop
bit, that is, 1
×
, 1.5
×
, or 2
×
bit times.
相關PDF資料
PDF描述
SC16C852LIB 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
SC16C852LIBS 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
SC16C852LIET 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
SC16C852SVIET 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
SC16C852VIET 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and XScale VLIO bus interface
相關代理商/技術參數
參數描述
SC16C850VIBS,115 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850VIBS,128 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850VIBS,151 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850VIBS,157 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850VIBS-F 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO VLIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*