- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C850VIBS (NXP Semiconductors N.V.) 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface PDF資料下載
參數資料
| 型號： | SC16C850VIBS |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| 封裝： | SC16C850VIBS<SOT617-1 (HVQFN32)|<<http://www.nxp.com/packages/SOT617-1.html<1<Always Pb-free,;SC16C850VIBS<SOT617-1 (HVQFN32)|<<http://www.nxp.com/packages/SOT617-1.html& |
| 文件頁數： | 16/48頁 |
| 文件大?。?/td> | 338K |
| 代理商： | SC16C850VIBS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SC16C850V
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 19 January 2011
16 of 48
NXP Semiconductors
SC16C850V
Single UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
6.13 RS-485 Features
6.13.1
Auto RS-485 RTS control
Normally the RTS pin is controlled by MCR bit 1, or if hardware flow control is enabled, the
logic state of the RTS pin is controlled by the hardware flow control circuitry. EFCR2
register bit 4 will take the precedence over the other two modes; once this bit is set, the
transmitter will control the state of the RTS pin. The transmitter automatically asserts the
RTS pin (logic 0) once the host writes data to the transmit FIFO, and de-asserts the RTS
pin (logic 1) once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode, the software would have to disable the hardware flow
control function.
6.13.2
RS-485 RTS inversion
EFCR2 bit 5 reverses the polarity of the RTS pin if the UART is in auto RS-485 RTS
mode.
When the transmitter has data to be sent, it will de-assert the RTS pin (logic 1), and when
the last bit of the data has been sent out, the transmitter asserts the RTS pin (logic 0).
6.13.3
Auto 9-bit mode (RS-485)
EFCR2 bit 0 is used to enable the 9-bit mode (Multi-drop or RS-485 mode). In this mode
of operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the auto 9-bit mode the software would have to disable the hardware and software
flow control functions.
6.13.3.1
Normal Multi-drop mode
The 9-bit Mode in EFCR (bit 0) is enabled, but not Special Character Detect (EFR bit 5).
The receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER bit 2 must be set to ‘1’ at
this time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller take no further action, the receiver will
receive the subsequent data.
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C852LIB | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface |
| SC16C852LIBS | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface |
| SC16C852LIET | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface |
| SC16C852SVIET | 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| SC16C852VIET | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and XScale VLIO bus interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C850VIBS,115 | 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS,128 | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS,151 | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS,157 | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS-F | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO VLIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。