- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C850VIBS (NXP Semiconductors N.V.) 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface PDF資料下載
參數資料
| 型號： | SC16C850VIBS |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| 封裝： | SC16C850VIBS<SOT617-1 (HVQFN32)|<<http://www.nxp.com/packages/SOT617-1.html<1<Always Pb-free,;SC16C850VIBS<SOT617-1 (HVQFN32)|<<http://www.nxp.com/packages/SOT617-1.html& |
| 文件頁數： | 5/48頁 |
| 文件大?。?/td> | 338K |
| 代理商： | SC16C850VIBS |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SC16C850V
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 19 January 2011
5 of 48
NXP Semiconductors
SC16C850V
Single UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
[1]
HVQFN32 package die supply ground is connected to both V
SS
pin and exposed center pad. V
SS
pin must be connected to supply
ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be
soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias
need to be incorporated in the printed-circuit board in the thermal pad region.
INT
20
O
Interrupt output.
The output state is defined by the user through the software setting of
MCR[5]. INT is set to the active mode when MCR[5] is set to a logic 0. INT is set to the
open-source mode when MCR[3] is set to a logic 1. See
Table 19
.
Read strobe (active LOW).
A HIGH to LOW transition on this signal starts the read cycle.
The SC16C850V reads a byte from the internal register and puts the byte on the data bus
for the host to retrieve.
Write strobe (active LOW).
A HIGH to LOW transition on this signal starts the write cycle,
and a LOW to HIGH transition transfers the data on the data bus to the internal register.
Latch Lower Address (active LOW).
A logic LOW on this pin puts the VLIO interface in the
address phase of the transaction, where the lower 8 bits of the VLIO (specifying the UART
register and the channel address) are loaded into the address latch of the device through
the AD7 to AD0 bus. A logic HIGH puts the VLIO interface in the data phase where data can
are transferred between the host and the UART.
Low Power.
When asserted (active HIGH), the device immediately goes into low-power
mode. The oscillator is shut-off and some host interface pins are isolated from the host’s bus
to reduce power consumption. The device only returns to normal mode when the LOWPWR
pin is de-asserted. On the negative edge of a de-asserting LOWPWR signal, the device is
automatically reset and all registers return to their default reset states. This pin has an
internal pull-down resistor, therefore, it can be left unconnected.
not connected
IOR
14
I
IOW
12
I
LLA
19
I
LOWPWR 9
I
n.c.
2, 15, 16,
17, 18
23
-
RESET
I
Master reset (active LOW).
A reset pulse will reset the internal registers and all the outputs.
The SC16C850V transmitter outputs and receiver inputs will be disabled during reset time.
(See
Section 7.23 “SC16C850V external reset condition and software reset”
for initialization
details.)
Ring Indicator (active LOW).
A logic 0 on this pin indicates the modem has received a
ringing signal from the telephone line. A logic 1 transition on this input pin will generate an
interrupt is modem status interrupt is enabled. Status can be tested by reading MCR[6].
Request to Send (active LOW).
A logic 0 on the RTS pin indicates the transmitter has data
ready and waiting to send. Writing a logic 1 in the modem control register MCR[1] will set
this pin to a logic 0, indicating data is available. After a reset this pin will be set to a logic 1.
UART receive data.
The RX signal will be a logic 1 during reset, idle (no data), or when not
receiving data. During the local Loopback mode, the RX input pin is disabled and TX data is
connected to the UART RX input internally.
UART transmit data.
The TX signal will be a logic 1 during reset, idle (no data), or when the
transmitter is disabled. During the local Loopback mode, the TX output pin is disabled and
TX data is internally connected to the UART RX input.
Power supply input.
Signal and power ground.
Crystal or external clock input.
Functions as a crystal input or as an external clock input. A
crystal can be connected between this pin and XTAL2 to form an internal oscillator circuit.
Alternatively, an external clock can be connected to this pin to provide custom data rates
(see
Section 6.9 “Programmable baud rate generator”
). See
Figure 4
.
Output of the crystal oscillator or buffered clock.
Crystal oscillator output or buffered
clock output. Should be left open if an external clock is connected to XTAL1.
RI
27
I
RTS
21
O
RX
6
I
TX
7
O
V
DD
V
SS
XTAL1
28
13
[1]
10
I
I
I
XTAL2
11
O
Table 2.
Symbol
Pin description
…continued
Pin
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C852LIB | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface |
| SC16C852LIBS | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface |
| SC16C852LIET | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface |
| SC16C852SVIET | 1.8 V dual UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface |
| SC16C852VIET | 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and XScale VLIO bus interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C850VIBS,115 | 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS,128 | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS,151 | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS,157 | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C850VIBS-F | 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO VLIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。