- 您現在的位置：買賣IC網 > PDF目錄1967 > SC16C852VIET,151 (NXP Semiconductors)IC UART DUAL W/FIFO 36TFBGA PDF資料下載
參數資料
| 型號： | SC16C852VIET,151 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 11/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART DUAL W/FIFO 36TFBGA |
| 標準包裝： | 490 |
| 特點： | 可編程 |
| 通道數： | 2，DUART |
| FIFO's： | 128 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-TFBGA |
| 供應商設備封裝： | 36-TFBGA（3.5x3.5） |
| 包裝： | 托盤 |
| 其它名稱： | 568-5662 935282518151 SC16C852VIET,151-ND SC16C852VIET-S SC16C852VIET-S-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
SC16C852V
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 21 January 2011
19 of 55
NXP Semiconductors
SC16C852V
Dual UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
6.14 RS-485 features
6.14.1 Auto RS-485 RTS control
Normally the RTSx pin is controlled by MCR bit 1, or if hardware flow control is enabled,
the logic state of the RTSx pin is controlled by the hardware flow control circuitry. EFCR2
register bit 4 will take the precedence over the other two modes; once this bit is set, the
transmitter will control the state of the RTSx pin. The transmitter automatically asserts the
RTSx pin (logic 0) once the host writes data to the transmit FIFO, and de-asserts the
RTSx pin (logic 1) once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode, the software would have to disable the hardware flow
control function.
6.14.2 RS-485 RTS inversion
EFCR2 bit 5 reverses the polarity of the RTSx pin if the UART is in auto RS-485 RTS
mode.
When the transmitter has data to be sent, it will de-assert the RTSx pin (logic 1), and
when the last bit of the data has been sent out, the transmitter asserts the RTS pin
(logic 0).
6.14.3 Auto 9-bit mode (RS-485)
EFCR2 bit 0 is used to enable the 9-bit mode (Multi-drop or RS-485 mode). In this mode
of operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the auto 9-bit mode the software would have to disable the hardware and software
flow control functions.
6.14.3.1
Normal Multi-drop mode
The 9-bit Mode in EFCR (bit 0) is enabled, but not Special Character Detect (EFR bit 5).
The receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER bit 2 must be set to ‘1’ at
this time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller take no further action, the receiver will
receive the subsequent data.
相關PDF資料 |
PDF描述 |
|---|---|
| SC16IS741IPW,112 | IC UART 16TSSOP |
| SC16IS750IBS,151 | IC UART I2C/SPI 24-HVQFN |
| SC16IS762IBS,151 | IC UART DUAL I2C/SPI 32-HVQFN |
| SC26C92A1N,112 | IC UART 40-DIP |
| SC28C94A1A,512 | IC UART QUAD W/FIFO 52-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C852VIET-G | 功能描述:UART 接口集成電路 1.8V 2CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C852VIET-S | 功能描述:UART 接口集成電路 1.8V 2CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16DP-26 | 制造商:Thomas & Betts 功能描述:SAXXIT CABLE CLIP W/ DRIVE PIN -7 制造商:Belden Inc 功能描述: |
| SC16DP-3Q | 制造商:Thomas & Betts 功能描述:SAXXIT CABLE CLIP W/ DRIVE PIN -8 |
| SC16-FM-M16-NPB-ML-1 | 制造商:HellermannTyton 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。