參數資料
型號： TH50VSF2581AASB
廠商： Toshiba Corporation
元件分類： 圓形連接器
英文描述： Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:7; Connector Shell Size:18; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight
中文描述： SRAM和閃存混合多芯片封裝
文件頁數： 23/50頁
文件大?。?/td> 546K
代理商： TH50VSF2581AASB
TH50VSF2580/2581AASB
2001-10-26 23/50
Program Suspend/Resume Mode
Program Suspend is used to enable Data Read by suspending the Write operation. The device accepts a
Program Suspend command in Write Mode (including Write operations performed during Erase Suspend) but
ignores the command in other modes. When the command is input, the address of the bank on which Write is
being performed must be specified. After input of the command, the device will enter Program Suspend Read
Mode after t
SUSP
.
During Program Suspend, Cell Data Read, ID Read and CFI Data Read can be performed. When Data Write
is suspended, the address to which Write was being performed becomes undefined. ID Read and CFI Data Read
are the same as usual.
After completion of Program Suspend input a Program Resume command to return to Write Mode. When
inputting the command, specify the address of the bank on which Write is being performed. If the ID Read or
CFI Data Read functions is being used, abort the function before inputting the Resume command. On receiving
the Resume command, the device returns to Write Mode and resumes outputting the Hardware Sequence flag
for the bank to which data is being written.
Program Suspend can be run in Fast Program Mode or Acceleration Mode. However, note that when running
Program Suspend in Acceleration Mode, V
ACC
must not be released.
Auto Chip Erase Mode
The Auto Chip Erase Mode is set using the Chip Erase command. An Auto Chip Erase operation starts on the
rising edge of WE in the sixth bus cycle. All memory cells are automatically preprogrammed to 0, erased and
verified as erased by the chip. The device status is indicated by the Hardware Sequence flag.
Command input is ignored during an Auto Chip Erase. A hardware reset can interrupt an Auto Chip Erase
operation. If an Auto Chip Erase operation is interrupted, it cannot be completed correctly. Hence an additional
Erase operation must be performed.
Any attempt to erase a protected block is ignored. If all blocks are protected, the Auto Erase operation will not
be executed and the device will enter Read mode 100
μ
s after the rising edge of the WE signal in the sixth bus
cycle.
If an Auto Chip Erase operation fails, the device will remain in the erasing state and will not return to Read
Mode. The device status is indicated by the Hardware Sequence flag. Either a Reset command or a hardware
reset is required to return the device to Read Mode after a failure.
In this case it cannot be ascertained which block the failure occurred in. Either abandon use of the device
altogether, or perform a Block Erase on each block, identify the failed block, and stop using it. The host
processor must take measures to prevent subsequent use of the failed block.
相關PDF資料
PDF描述
TH50VSF3582AASB TOSHIBA MULTI-CHIP INTEGRATED CIRCUIT SILICON GATE CMOS
TH50VSF3583AASB TOSHIBA MULTI-CHIP INTEGRATED CIRCUIT SILICON GATE CMOS
TH50VSF3680 0.4W, 75V, 0.3A, SIGNAL DIODE, SOD123
TH50VSF3681AASB GT 10C 10#16 SKT RECP BOX RM
TH513 RF & MICROWAVE TRANSISTORS HF SSB APPLICATIONS
相關代理商/技術參數
參數描述
TH50VSF2582 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SRAM AND FLASH MEMORY MIXED MULTI-CHIP PACKAGE
TH50VSF2582AASB 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SRAM AND FLASH MEMORY MIXED MULTI-CHIP PACKAGE
TH50VSF2583AASB 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:SRAM AND FLASH MEMORY MIXED MULTI-CHIP PACKAGE
TH50VSF3582AASB 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA MULTI-CHIP INTEGRATED CIRCUIT SILICON GATE CMOS
TH50VSF3583AASB 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA MULTI-CHIP INTEGRATED CIRCUIT SILICON GATE CMOS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*