參數資料
型號： TLV320AIC3110IRHBT
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻／視頻放大
英文描述： AUDIO AMPLIFIER, PQCC32
封裝： 5 X 5 MM, GREEN, PLASTIC, QFN-32
文件頁數： 81/126頁
文件大?。?/td> 1528K
代理商： TLV320AIC3110IRHBT
SLAS647 – DECEMBER 2009
www.ti.com
Following the beep volume control is a digital mixer that mixes in a playback data stream whose level has
already been set by the DAC volume control. Therefore, once the key-click volume level is set, the
key-click volume is not affected by the DAC volume control, which is the main control available to the end
user. This functionality is shown in Figure 1-1.
Following the DAC, the signal can be further scaled by the analog output volume control and power
amplifier level control.
The beep generator is used for the key-click function. A single beep is generated by writing to page 0 /
register 71, bit D7. After the programmed beep length has finished, register 71, bit D7 is reset back to
zero.
5.5.6
Programming DAC Digital Filter Coefficients
The digital filter coefficients must be programmed through the I2C interface. All digital filtering for the DAC
signal path must be loaded into the RAM before the DAC is powered on. (Note that default ALLPASS filter
coefficients for programmable biquads are located in boot ROM. The boot ROM automatically loads the
default values into the RAM following a hardware reset (toggling the RESET pin) or after a software reset.
After resetting the device, loading boot ROM coefficients into the digital filters requires 100
μs of
programming time. During this time, reading or writing to page 8 through page 15 for updating DAC filter
coefficient values is not permitted. (The DAC should not be powered up until after all of the DAC
configurations have been done by the system microprocessor.)
5.5.7
Updating DAC Digital Filter Coefficients During PLAY
When it is required to update the DAC digital filter coefficients or beep generator during play, care must be
taken to avoid click and pop noise or even a possible oscillation noise. These artifacts can occur if the
DAC coefficients are updated without following the proper update sequence. The correct sequence is
shown in Figure 5-35. The values for times listed in Figure 5-35 are conservative and should be used for
software purposes.
There is also an adaptive mode, in which DAC coefficients can be updated while the DAC is on. For
details, see Section 5.5.1.3.
58
APPLICATION INFORMATION
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TLV320AIC3110
相關PDF資料
PDF描述
TLV320AIC3111IRHBT AUDIO AMPLIFIER, PQCC32
TLV320AIC3111IRHBR AUDIO AMPLIFIER, PQCC32
TLV320AIC3120IRHBR AUDIO AMPLIFIER, PQCC32
TLV320AIC3120IRHBT AUDIO AMPLIFIER, PQCC32
TLV320AIC31IRHBRG4 SPECIALTY CONSUMER CIRCUIT, PQCC32
相關代理商/技術參數
參數描述
TLV320AIC3111 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power Audio Codec With Embedded miniDSP and Stereo Class-D Speaker Amplifier
TLV320AIC3111_101 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power Audio Codec With Embedded miniDSP and Stereo Class-D Speaker Amplifier
TLV320AIC3111EVM-K 功能描述:音頻 IC 開發工具 TLV320AIC3111 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TLV320AIC3111IRHBR 功能描述:接口—CODEC Low-Pwr Audio CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC3111IRHBT 功能描述:接口—CODEC Low-Pwr Audio CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*