參數資料
型號： TMS320C10-25
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： Digital Signal Processors(160ns指令周期，分離的程序和數據總線，外部輪詢中斷的DSP)
中文描述： 數字信號處理器（160ns指令周期，分離的程序和數據總線，外部輪詢中斷的數字信號處理器）
文件頁數： 50/139頁
文件大?。?/td> 1478K
代理商： TMS320C10-25
tw(PGM)
Initial program pulse duration
TMS320E14, TMS320P14
DIGITAL SIGNAL PROCESSORS
SPRS009C–JANUARY 1987–REVISED JULY 1991
POST OFFICE BOX 1443
HOUSTON, TEXAS 77001
50
erasure
Before programming, the
′
E14 must be erased by exposing it to ultraviolet light. The recommended minimum
exposure dose (UV-intensity
×
exposure-time) is 15 W
s/cm
2
. A typical 12-mW
s/cm
2
, filterless UV lamp will
erase the device in 21 minutes. The lamp should be located about 2.5 cm above the chip during erasure. After
exposure, all bits are in the high state.
verify/read
To verify correct programming, the EPROM cell can be read using either the verify or read line definitions shown
in Table 5, assuming the inhibit bit (RBIT) has not been programmed.
program inhibit
Programming may be inhibited by maintaining a high level input on the E pin or PGM pin.
standard programming procedure
Before programming, the
′
E14 must first be completely erased. The device can then be programmed with the
correct code. It is advisable to program unused sections with zeros as a further security measure. After the
programming is complete, the code programmed into the cell should be verified. If the cell passes verification,
the next step is to program the ROM protect bit (RBIT). Once the RBIT programming is verified, an opaque label
should be placed over the window to protect the EPROM cell from inadvertent erasure by ambient light. At this
point, the programming is complete, and the device is ready to be placed into its destination circuit.
Refer to other appendices of the TMS320C1x User’s Guidefor additional information on EPROM programming.
recommended timing requirements for programming: V
CC
= 6 V and V
PP
= 12.5 V (FAST) or
V
CC
= 6.5 V and V
PP
= 13 V (SNAP! PULSE), T
A
= 25
°
C (see Note 13)
MIN
NOM
MAX
UNIT
Fast programming algorithm
0.95
1
1.05
ms
μ
s
ms
μ
s
μ
s
μ
s
μ
s
μ
s
μ
s
μ
s
μ
s
SNAP! Pulse programming algorithm
95
100
105
tw(FPGM)
tsu(A)
tsu(E)
tsu(G)
tsu(D)
tsu(VPP)
tsu(VCC)
th(A)
th(D)
NOTE 13: For all switching characteristics and timing measurements, input pulse levels are 0.4 V to 2.4 V and VPP = 12.5 V
±
0.5 V during
programming.
Final pulse duration
Fast programming only
2.85
78.75
Address setup time
2
E setup time
2
G setup time
2
Data setup time
2
VPP setup time
VCC setup time
Address hold time
2
2
0
Data hold time
2
相關PDF資料
PDF描述
TMS320C15-25 Digital Signal Processors(160ns指令周期，分離的程序和數據總線，外部輪詢中斷的DSP)
TMS320LC17 Digital Signal Processors(278ns指令周期，分離的程序和數據總線，外部輪詢中斷的DSP)
TMS320C203(中文) Digital Signal Processors(50ns指令周期， 空閑狀態CPU全關斷，先進的外圍，多種PLL可選)
TMS320VC203(中文) Digital Signal Processors(50ns指令周期， 空閑狀態CPU全關斷，先進的外圍，多種PLL可選)
TMS320C209(中文) Digital Signal Processors(35ns和50ns指令周期，空閑狀態CPU全關斷，先進的外圍，多種PLL可選)
相關代理商/技術參數
參數描述
TMS320C10-25FNL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor
TMS320C10FNA 制造商:TI 制造商全稱:Texas Instruments 功能描述:DIGITAL SIGNAL PROCESSORS
TMS320C10FNL 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:
TMS320C10FNL14 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor
TMS320C10FNL25 功能描述:數字信號處理器和控制器 - DSP, DSC CMOS 32010 PLCC 25MHZ RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*