- 您現在的位置：買賣IC網 > PDF目錄19343 > TMS320C6414TGLZ7 (Texas Instruments)IC DSP FIXED-POINT 532-FCBGA PDF資料下載
參數資料
| 型號： | TMS320C6414TGLZ7 |
| 廠商： | Texas Instruments |
| 文件頁數： | 119/146頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP FIXED-POINT 532-FCBGA |
| 標準包裝： | 60 |
| 系列： | TMS320C6414T/15T/16T |
| 類型： | 定點 |
| 接口： | 主機接口，McBSP，PCI，UTOPIA |
| 時鐘速率： | 720MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 1.03MB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.20V |
| 工作溫度： | 0°C ~ 90°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 532-BFBGA，F(xiàn)CBGA |
| 供應商設備封裝： | 532-FCBGA（23x23） |
| 包裝： | 托盤 |
| 配用： | TMDXEVM6452-ND - TMDXEVM6452 296-23038-ND - DSP STARTER KIT FOR TMS320C6416 |
| 其它名稱： | 296-17757 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁當前第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
TMS320C6414T, TMS320C6415T, TMS320C6416T
FIXEDPOINT DIGITAL SIGNAL PROCESSORS
SPRS226M NOVEMBER 2003 REVISED APRIL 2009
74
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
IEEE 1149.1 JTAG compatibility statement
The TMS320C6414T/15T/16T DSP requires that both TRST and RESET be asserted upon power up to be
properly initialized. While RESET initializes the DSP core, TRST initializes the DSP’s emulation logic. Both
resets are required for proper operation.
Note: TRST is synchronous and must be clocked by TCLK; otherwise, BSCAN may not respond as expected
after TRST is asserted.
While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the
DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface
and DSP’s emulation logic in the reset state. TRST only needs to be released when it is necessary to use a JTAG
controller to debug the DSP or exercise the DSP’s boundary scan functionality. RESET must be released only
in order for boundary-scan JTAG to read the variant field of IDCODE correctly. Other boundary-scan instructions
work correctly independant of current state of RESET.
For maximum reliability, the TMS320C6414T/15T/16T DSP includes an internal pulldown (IPD) on the TRST
pin to ensure that TRST will always be asserted upon power up and the DSP’s internal emulation logic will
always be properly initialized. JTAG controllers from Texas Instruments actively drive TRST high. However,
some third-party JTAG controllers may not drive TRST high but expect the use of a pullup resistor on TRST.
When using this type of JTAG controller, assert TRST to initialize the DSP after powerup and externally drive
TRST high before attempting any emulation or boundary scan operations.
Following the release of RESET, the low-to-high transition of TRST must be “seen” to latch the state of EMU1
and EMU0. The EMU[1:0] pins configure the device for either Boundary Scan mode or Emulation mode. For
more detailed information, see the terminal functions section of this data sheet.
Note: The DESIGN_WARNING section of the C6414T, C6415T, C6416T GLZ BSDL file contains information
and constraints regarding proper device operation while in Boundary Scan Mode.
For more detailed information on the C6414T/15T/16T JTAG emulation, see the TMS320C6000 DSP Designing
for JTAG Emulation Reference Guide (literature number SPRU641).
EMIF device speed
The rated EMIF speed, referring to both EMIFA and EMIFB, of these devices only applies to the SDRAM
interface when in a system that meets the following requirements:
1 chip-enable (CE) space (maximum of 2 chips) of SDRAM connected to EMIF
up to 1 CE space of buffers connected to EMIF
EMIF trace lengths between 1 and 3 inches
166-MHz SDRAM for 133-MHz operation (applies only to EMIFA)
143-MHz SDRAM for 100-MHz operation
Timing analysis must be done to verify all AC timings are met for all configurations. Verification of AC timings
is mandatory when using configurations other than those specified above. TI recommends utilizing I/O buffer
information specification (IBIS) to analyze all AC timings.
To properly use IBIS models to attain accurate timing analysis for a given system, see the Using IBIS Models
for Timing Analysis application report (literature number SPRA839).
To maintain signal integrity, serial termination resistors should be inserted into all EMIF output signal lines (see
the Terminal Functions table for the EMIF output signals).
相關PDF資料 |
PDF描述 |
|---|---|
| EEM06DTBN-S189 | CONN EDGECARD 12POS R/A .156 SLD |
| EMM43DTAD | CONN EDGECARD 86POS R/A .156 SLD |
| A3P400-FGG484 | IC FPGA 194I/O 484FBGA |
| 5173279-2 | CONN D-PLUG FEM SCKT 40POS VERT |
| AMM18DRAS | CONN EDGECARD 36POS .156 R/A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMS320C6414TGLZ8 | 制造商:Rochester Electronics LLC 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR - Bulk 制造商:Texas Instruments 功能描述: |
| TMS320C6414TGLZA6 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| TMS320C6414TGLZA7 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMS320C6414TGLZA8 | 制造商:Rochester Electronics LLC 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSOR - Bulk 制造商:Texas Instruments 功能描述: |
| TMS320C6414TUGLZA8 | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。