- 您現在的位置：買賣IC網 > PDF目錄98279 > TPS2306DWG4 (TEXAS INSTRUMENTS INC) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 PDF資料下載
參數資料
| 型號： | TPS2306DWG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 17/29頁 |
| 文件大?。?/td> | 427K |
| 代理商： | TPS2306DWG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
TPS2306
DUAL SEQUENCING HOT SWAP POWER MANAGER
SLVS368 APRIL 2001
24
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
t
UP2 ^
C
L1
V
RAMP *
V
UV1
IMAX
1 *
I
L1
) t
VUV1
Once the total delay to the secondary channel start-up (tUP2) is known, substitution of the secondary channel
parameters into equations 21 and 22 (or 23) can be used to determine the total system start-up time. Substitute
τSS2 for τSS1, IMAX2 for IMAX1, etc. However, for these calculations, the constant t1 in equations 21 and 22
is now the quantity (tUP2 + tSR). This version of equation 21 is used to determine the time at which the secondary
channel load starts up, tVUV2 when v2(t) = VUV2. Finally, the system start-up time is calculated by substituting
the secondary channel parameters into equation 22 (or 23) (including tVUV2 for tVUV1) to model ν2(t) when the
output voltage is above the UVLO threshold.
setting the linear mode timeout
Once an estimate of the required charging time is obtained, the value of the timing capacitor CT can be derived.
Since the timeout is obtained via the constant-current charging of the external capacitor, the minimum capacitor
value is given by:
C
T(min) +
i
CT(max)
t
ST
V
F(min)
^ 48
10*6
t
ST
where:
i
CT(MAX) = the maximum CT charging current, 65 A
V
F(MIN) = the minimum fault threshold on the CT pin, 1.35 V
For the example application, a total start-up time of about 2.03 ms was obtained. Solving equation 24 using this
timeout value produces a result of CT(MIN) = 0.097 F; a 0.1-F value is shown in the schematic.
using the FAULT output
LED indicator
The TPS2306 FAULT output provides fault reporting capability to the system host. It is an open-drain output
which becomes high-impedance under any conditions which cause either of the GATEx outputs to be turned
off. It can be used to provide a visual indication of a fault by using it as an LED pre-driver, as shown in Figure 7.
(23)
(24)
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2340APFPRG4 | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP80 |
| TPS2341PHPR | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| TPS2343DDPG3 | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO80 |
| TPS2343DDPR | 6-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO80 |
| TPS2345PWNRND | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2306EVM-001 | 功能描述:EVALUATION MODULE FOR TPS2306 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| TPS230QP | 制造商:Texas Instruments 功能描述: |
| TPS2310IPW | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWR | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。