參數資料
型號： TPS65185RSLT
廠商： TEXAS INSTRUMENTS INC
元件分類： 電源管理
英文描述： POWER SUPPLY SUPPORT CKT, PQCC48
封裝： 6 X 6 MM, 0.4 MM PITCH, 0.9 MM HEIGHT, PLASTIC, VQFN-48
文件頁數： 11/49頁
文件大?。?/td> 2488K
代理商： TPS65185RSLT
PRODUCTPREVIEW
SLVSAQ8A
– FEBRUARY 2011 – REVISED MAY 2011
VPOS/VNEG SUPPLY TRACKING
LDO1 (VPOS) and LDO2 (VNEG) track each other in a way that they are of opposite sign but same magnitude.
The sum of VLDO1 and VLOD2 is guaranteed to be
< 50 mV.
V3P3 POWER SWITCH
The integrated power switch is used to cut the 3.3-V supply to the EPD panel and is controlled through the
V3P3_EN pin of the ENABLE register. In SLEEP mode the switch is automatically turned off and its output is
discharged to ground. The default power-up state is OFF. To turn the switch ON, set the V3P3_ENbit to 1.
VCOM ADJUSTMENT
VCOM is the output of a power-amplifier with an output voltage range of 0 V to -5.11 V, adjustable in 10-mV
steps. In a typical application VCOM is connected to the VCOM terminal of the EPD panel and the amplifier is
controlled through the VCOM_CTRL pin. With VCOM_CTRL high, the amplifier drives the VCOM pin to the
voltage specified by the VCOM1 and VCOM2 register. When pulled low, the amplifier turns off and VCOM is
actively discharged to ground through VCOM_DIS pin. If active discharge is not desired, simply leave the
VCOM_DIS pin open.
For ease of design, the VCOM_CTRL pin may also be tied to the battery or IO supply. In this case, VCOM is
enabled with STROBE4 during the power-up sequence and disabled on STROBE1 of the power-down sequence.
Therefore VCOM is the last rail to be enabled and the first to be disabled.
KICK-BACK VOLTAGE MEASUREMENT
TPS65185 can perform a voltage measurement on the VCOM pin to determine the kick-back voltage of the
panel. This allows in-system calibration of VCOM. To perform a kick-back voltage measurement, follow these
steps:
Pull the WAKEUP pin and the PWRUP pin high to enable all output rails.
Set the HiZ bit in the VCOM2 register. This puts the VCOM pin in a high-impedance state.
Drive the panel with the Null waveform. Refer to E-Ink specification for detail.
Set the ACQ bit in the VCOM2 register to 1. This starts the measurement routine.
When the measurement is complete, the ACQC (Acquisition Complete) bit in the INT1 register is set and the
nINT pin is pulled low.
The measurement result is stored in the VCOM[8:0] bits of the VCOM1 and VCOM2 register.
Please note that the measurement result is not automatically programmed into non-volatile memory. Changing
the power-up default is described in the following paragraph.
STORING THE VCOM POWER-UP DEFAULT VALUE IN MEMORY
The power-up default value of VCOM can be user-set and programmed into non-volatile memory. To do so, write
the default value to the VCOM[8:0] bits of the VCOM1 and VCOM2 register, then set the PROG bit in VCOM2
register to 1. First, all power rails are shut-down, then the VCOM[8:0] value is committed to non-volatile memory
such that it becomes the new power-up default. Once programming is complete, the PRGC bit in the INT1
register is set and the nINT pin is pulled low. To verify that the new value has been saved properly, first write the
VCOM[8:0] bits to 0x000h, then pull the WAKEUP pin low. After the WAKEUP pin is pulled back high, read the
VCOM[8:0] bits to verify that the new default value is correct.
Copyright
2011, Texas Instruments Incorporated
19
相關PDF資料
PDF描述
TPS65200YFFR 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA36
TPS65251RHAT SWITCHING REGULATOR, PQCC40
TPS65251RHAR SWITCHING REGULATOR, PQCC40
TPS65257RHAT 4 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PQCC40
TPS65510RGTRG4 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16
相關代理商/技術參數
參數描述
TPS65186RGZR 功能描述:其他電源管理 PMIC FOR E-INK PAPER DISPLAY RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel
TPS65186RGZT 功能描述:LCD Gamma緩沖器 PMIC FOR E-INK PAPER DISPLAY RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
TPS65190RHDR 功能描述:LCD 驅動器 10Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TPS65191RHBR 功能描述:LCD 驅動器 7Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TPS65192RHDR 功能描述:LCD 驅動器 9Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*