- 您現在的位置：買賣IC網 > PDF目錄98285 > TPS65185RSLT (TEXAS INSTRUMENTS INC) POWER SUPPLY SUPPORT CKT, PQCC48 PDF資料下載
參數資料
| 型號： | TPS65185RSLT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, PQCC48 |
| 封裝： | 6 X 6 MM, 0.4 MM PITCH, 0.9 MM HEIGHT, PLASTIC, VQFN-48 |
| 文件頁數： | 17/49頁 |
| 文件大小： | 2488K |
| 代理商： | TPS65185RSLT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
PRODUCTPREVIEW
S
A6 A5 A4 A3 A2 A1 A0
A
S7 S6 S5 S4 S3 S2 S1 S0
A
D7 D6 D5 D4 D3 D2 D1 D0
A
P
S
A
Start Condition
Acknowledge
A6
A0
...
Device Address
R/nW
Read / not Write
S7
S0
...
Sub-Address
D7
D0
...
Data
P
Stop Condition
R/nW
Slave Address + R/nW
Reg Address
Data
SLVSAQ8A
– FEBRUARY 2011 – REVISED MAY 2011
When the temperature is equal or greater than the TMST_HOT[3:0] threshold, the TMST_HOT interrupt bit of
the INT1 register is set, and the nINT pin is pulled low.
If the last temperature is different from the baseline temperature by
±2°C (default) or more, the DTX interrupt
bit of the INT1 register is set. The latest temperature becomes the new baseline temperature. Please note
that by default the DTX interrupt is disabled, i.e. the nINT pin is not pulled low unless the DTX_EN bit was
previously set high.
If the last temperature change is less than
±2°C (default), no action is taken.
TYPICAL APPLICATION OF THE TEMPERATURE MONITOR
In a typical application the temperature monitor and interrupts are used in the following manner:
After the WAKEUP pin has been pulled high, the Application Processor (AP) writes 0x80h to the TMST1
register (address 0x0Dh). This starts the temperature measurement.
The AP waits for the EOC interrupt. Alternatively the AP can poll the CONV_END bit in register TMST1. This
will notify the AP that the A/D conversion is complete and the new temperature reading is available in the
TMST_VALUE register (address (0x00h).
The AP reads the temperature value from the TMST_VALUE register (address (0x00h).
If the temperature changes by
±2°C (default) or more from the first reading, the processor is notified by the
DTX interrupt. The A/P may or may not decide to select a different set of wave forms to drive the panel.
If the temperature is outside the allowed operating range of the panel, the processor is notified by the THOT
and TCOLD interrupts, respectively. It may or may not decide to continue with the page update.
Once an over/under temperature has been detected, the AP should reset the TMST_HOT_EN or
TMST_COLD_EN bits, respectively, to avoid the nINT pin to be continuously pulled low. The TMST_HOT and
TMST_COLD interrupt bits then should be polled continuously, to determine when the panel temperature
recovers to the normal operating range. Once the temperature has recovered, the TMST_HOT_EN or
TMST_COLD_EN bits should be set to
‘1’ again and normal operation can resume.
I
2C BUS OPERATION
The TPS65185 hosts a slave I2C interface that supports data rates up to 400 kbit/s and auto-increment
addressing and is compliant to I2C standard 3.0.
Figure 28. Subaddress in I2C Transmission
The I2C Bus is a communications link between a controller and a series of slave terminals. The link is established
using a two-wire bus consisting of a serial clock signal (SCL) and a serial data signal (SDA). The serial clock is
sourced from the controller in all cases where the serial data line is bi-directional for data communication
between the controller and the slave terminals. Each device has an open drain output to transmit data on the
serial data line. An external pull-up resistor must be placed on the serial data line to pull the drain output high
during data transmission.
Data transmission is initiated with a start bit from the controller as shown in Figure 30. The start condition is
recognized when the SDA line transitions from high to low during the high portion of the SCL signal. Upon
reception of a start bit, the device will receive serial data on the SDA input and check for valid address and
control information. If the appropriate slave address bits are set for the device, then the device will issue an
acknowledge pulse and prepare to receive the register address. Depending on the R/nW bit, the next byte
received from the master is written to the addressed register (R/nW = 0) or the device responds with 8-bit data
from the register (R/nW = 1). Data transmission is completed by either the reception of a stop condition or the
24
Copyright
2011, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65200YFFR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA36 |
| TPS65251RHAT | SWITCHING REGULATOR, PQCC40 |
| TPS65251RHAR | SWITCHING REGULATOR, PQCC40 |
| TPS65257RHAT | 4 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PQCC40 |
| TPS65510RGTRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65186RGZR | 功能描述:其他電源管理 PMIC FOR E-INK PAPER DISPLAY RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel |
| TPS65186RGZT | 功能描述:LCD Gamma緩沖器 PMIC FOR E-INK PAPER DISPLAY RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| TPS65190RHDR | 功能描述:LCD 驅動器 10Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TPS65191RHBR | 功能描述:LCD 驅動器 7Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| TPS65192RHDR | 功能描述:LCD 驅動器 9Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。