- 您現在的位置：買賣IC網 > PDF目錄98302 > TSC2101IRGZRG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC48 PDF資料下載
參數資料
| 型號： | TSC2101IRGZRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| 封裝： | GREEN, PLASTIC, VQFN-48 |
| 文件頁數： | 30/95頁 |
| 文件大?。?/td> | 1217K |
| 代理商： | TSC2101IRGZRG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
TSC2101
SLAS392D JUNE 2003 REVISED MAY 2005
www.ti.com
36
The internal reference voltage should only be used in the single-ended mode for battery monitoring,
temperature measurement, and for utilizing the auxiliary inputs. Optimal touch-screen performance is achieved
when using a ratiometric conversion, thus all touch-screen measurements are done automatically in the
ratiometric mode.
An external reference can also be applied to the VREF pin, and the internal reference can be turned off.
Variable Resolution
The TSC2101 provides three different resolutions for the ADC: 8, 10 or 12 bits. Lower resolutions are often
practical for measurements such as touch pressure. Performing the conversions at lower resolution reduce the
amount of time it takes for the ADC to complete its conversion process, which lowers power consumption.
Conversion Clock and Conversion Time
The TSC2101 contains an internal 8 MHz clock, which is used to drive the state machines inside the device
that perform the many functions of the part. This clock is divided down to provide a clock to run the ADC. The
division ratio for this clock is set in the ADC control register. The ability to change the conversion clock rate
allows the user to choose the optimal value for resolution, speed, and power. If the 8 MHz clock is used directly,
the ADC is limited to 8-bit resolution; using higher resolutions at this speed does not result in accurate
conversions. Using a 4 MHz conversion clock is suitable for 10-bit resolution; 12-bit resolution requires that the
conversion clock run at 1 or 2 MHz.
Regardless of the conversion clock speed, the internal clock runs nominally at 8 MHz. The conversion time of
the TSC2101 is dependent upon several functions (see the section Touch Screen Conversion Initiated at Touch
Detect in this data sheet). While the conversion clock speed plays an important role in the time it takes for a
conversion to complete, a certain number of internal clock cycles are needed for proper sampling of the signal.
Moreover, additional times, such as the panel voltage stabilization time, can add significantly to the time it takes
to perform a conversion. Conversion time can vary depending upon the mode in which the TSC2101 is used.
Throughout this data sheet, internal and conversion clock cycles are used to describe the times that many
functions take to execute. Considering the total system design, these times must be taken into account by the
user.
When both the audio ADC and DAC are powered down, the touch screen ADC uses an internal oscillator for
conversions. However, to save power whenever audio ADC or DAC are powered up, the internal oscillator is
powered down and MCLK and BCLK are used to clock the touch screen ADC.
The TSC2101 uses the programmed value of bit D13 in control register 06H/page 2 and the PLL
programmability to derive a clock from MCLK. The various combinations are listed in Table 3.
Table 3. Conversion Clock Frequency
D13=0 (in control register 06H/page 2)
D13=1 (in control register 06H/page 2)
PLL enabled
160
13
×
P
K
MCLK
192
17
×
P
K
MCLK
PLL disabled
10
13
×
Q
MCLK
12
17
×
Q
MCLK
Touch Detect/Data Available
The pen interrupt/data available (PINTDAV) output function is detailed in Figure 28. While in the power-down
mode, the Y– driver is ON and connected to AVSS2 and the X+ pin is connected through an onchip pull-up
resistor to AVDD2. In this mode, the X+ pin is also connected to a digital buffer and mux to drive the PINTDAV
output. When the panel is touched, the X+ input is pulled to ground through the touch screen and pen-interrupt
signal goes LOW due to the current path through the panel to AVSS2, initiating an interrupt to the processor.
During the measurement cycles for X and Y position, the X+ input is disconnected from the pen-interrupt
circuit to prevent any leakage current from the pull-up resistor flowing through the touch screen, and thus
causing conversion errors.
相關PDF資料 |
PDF描述 |
|---|---|
| TSC2101IRGZG4 | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| TSC2111IRGZR | 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC48 |
| TSC2111IRGZT | 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC48 |
| TSC2111IRGZRG4 | 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC48 |
| TSC2111IRGZTG4 | 0.4 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSC2101RGZG4 | 制造商:Texas Instruments 功能描述:AUD CODEC 2ADC / 2DAC 32BIT 48QFN - Rail/Tube |
| TSC2101RGZRG4 | 制造商:Texas Instruments 功能描述:AUD CODEC 2ADC / 2DAC 32BIT 48QFN - Tape and Reel |
| TSC2102 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PROGRAMMABLE TOUCH SCREEN CONTROLLER WITH INTEGRATED STEREO AUDIO DAC AND HEADPHONE AMPLIFIER |
| TSC21020F | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Rad. Hard 32/40-bit IEEE Floating Point DSP |
| TSC21020F-20MA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Digital Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。